Introducing the TCMM-RC's Night Phoenix Freestyle FPV Drone! Includes bright LED lights, that brighten with the throttle, for night cruising, thus making it easier for you to spot your drone. The purple props and printed purple TPU parts make it an excellent freestyle drone during the day as well!

Note: PNP version, no receiver is included.

Features

• 7-24V wide input voltage with 5V for camera,12V typical corresponding current value:25mw-120mA 200mw-200mA 600mw-300mA 800mw-350mA
• Solid MMCX antenna connection and MMCX brass dipole antenna
• 3D Printed TPU parts for comprehensive security and protection
• 3K FULL CARBON FIBER Frame with CHAMFERED EDGES
• Support OSD Configuring via Betaflight FC
• One button frequency and power setup
• 25/200/600/800mw power switchable
• LED brightens with the throttle
• Fast, furious, and fun to fly
• 40 channels with MIC
• Support Smart audio
• Pitmode

F7 FC

• Single-panel design, with ESC pin pads on the back which greatly reduces the problem of soldering short-circuits when soldering wires.
• The flight controller reserves SH1.0 sockets and pads to meet both the requirements of free soldering operation and DIY soldering.
• On-board 10V and 5V BEC (input voltage 2-6S) provide a clearer image display effect for image transmission.
• TYPE-C interface which can support larger current and convenient for pilots' operating experience.
• Onboard barometer and a black box. Reserved compass, GPS interface.
• Up to 5 serial ports and 8 DShot output ports.

100A 4IN1 ESC

• Innovative structural design in the industry: the power board is separated from the control board. This design allows pilots to only replace the power board and minimize the error when replacing.
• Two current models, 100A and a 60A, to meet the needs of different levels of pilots.
• The layout of the control board adopts the principle of symmetrical aesthetics.
• Uses a 4Oz copper thickness that balances beauty and performance.

Transmitter VTX

• Copper skin can increase heat dissipation efficiency, avoid excessively high temperatures during work, and improve the stability of the board's working ability.
• There is a 1mm wide slot between the image transmission power board and the receiver to shield the signal and prevent emf interference.
• Reserve the receiver installation position so the receiver will no longer be jammed in hard-to-reach places.
• 800mW image transmission, more user-friendly LED indication mode, clear at a glance.
• Onboard microphone with immersive sound for an overall better FPV experience.
• All wireless modules are placed on one board, which is more reasonable.

Specifications

• Camera: FOXEER Arrow MICRO PRO / 600TVL
• Antenna: RHCP Omnidirectional antenna
• Flight Controller: MCU STM32F722
• Propeller: T5046C three-blade 
• VTX: TX5804 25-800MW
• ESC: 32-bit 100A ESC
• Motor: 2306 2450KV
• Wheelbase: 220mm
• Weight: 426.0g

Frame

• Flight control hole spacing：M3x20x20/M3x30.5x30.5mm
• Motor hole spacing：M3x16x16mm M3x19x19mm
• Material Science：3k Carbon fiber matte
• Thickness of upper plate: 2mm
• Camera adaptation：19mm
• Base plate thickness: 2mm
• X plate thickness: 2mm
• Boom thickness: 5mm
• Wheelbase: 225mm

QN2306-2450KV Motors (Purple)

• Motor Resistance (RM)：0.0412 Ω
• Max Continuous Current：49.5A
• Max Continuous Power：792W
• Overall Shaft Length：32.9mm
• Bolt holes spacing：19/16mm
• Motor Body Length：18.4mm
• Idle Current (Io/10V)：2.6A
• Motor Diameter：28.5mm
• Configu-ration：12N/14P
• Motor KV：2450RPM/V
• Stator Diameter：23mm
• Stator Thickness：6mm
• Prop adapter shaft：M5
• Max thrust：1510g
• Bolt thread：M3
• Lipo Cell：3-4S
• Propeller：5”/6”
• Weight：35.6g

100A ESC 3-6S

• Mounting Hole: M3*30.5*30.5 mm
• Peak current:120A（5S）
• Input voltage:3-6 S Lipo
• Constant current:100A
• Protocol: DSHOT1200
• MCU:STM32F051
• Firmware: BL_32
• MOS Tube:5×6
• BEC output: NO
• Name: E100

F7 FC

• Mounting Hole: M3*30.5*30.5 mm
• BEC:10V 2A, 5V 2A,4.5V,3.3V
• Support Receiver: PPM,Ibus,
• Firmware: DARWINF722HD
• Betaflight OSD: AT7456E
• Input voltage:3-6 S Lipo
• Buzzer interface: YES
• MCU:STM32F722
• Gyro: MPU6000
• Barometer: YES
• Black box:YES
• Sbus, Dsmx

FOXEER Arrow MICRO PRO Camera

• Image sensor: 1 / 3 "Sony super had II CCD + next chip 2040 DSP
• Pixels: pal: 976 (H) x 494 (V); NTSC: 768 (H) x 494 (V)
• Resolution: 600TVL (color) 650tvl (black and white)
• Default modes: def, vivacive, sunny, cloud, led TR, usr1
• OSD: edit name, power supply, flight time
• Size: 18.5 * 19mm (excluding bracket)
• Storage temperature: - 40 C ~ 60 C
• Working temperature: - 10C ~ 50c
• OSD programming board: support
• Weight: 5.3g (excluding bracket)
• Minimum illumination: 0.01LUX
• Image adjustment: supported
• Power consumption: 70ma
• Low-pressure alarm: support
• Synchronization: internal
• White spot fix: support
• Camera Title: support
• Input power: 5-40v
• TV system: pal
• WDR: support
• DNR:2D DNR

FPV Transmitter VTX

• Output power: 25mW/200mW/600mW/800mW switchable
• Dimensions: 36mm*22mm*5mm,30.5 stackable hole
• 5V camera supply: 200mA(MAX)----200mW@12V
• 5V camera supply: 300mA(MAX)----600mW@12V
• 5V camera supply: 350mA(MAX)----800mW@12V
• 5V camera supply: 120mA(MAX)----25mW@12V
• Power supply: 5V output for Camera
• Item name: FPV Transmitter VTX
• Weight: 8g(excluding antenna)
• Cable connector: Solder pads
• Extra features: Smart audio
• Antenna connector: MMCX
• Input  voltage: 7V~24V
• Frequency: 5.8G
• Channels: 40CH

DALPROP T5046C Propeller

• Product Name: 5046 propeller
• Material: imported Bayer PC
• Quantity: 4 pairs (8 pieces)
• Screw diameter: 127mm
• Center thickness: 7mm
• Specification: 5046 * 3
• Brand name: dalprop
• Color: transparent
• Weight: 5.1g/piece

Button Control Channel Select Mode

Power select

• Press button for 4S, Red LED will flash, then select power by simple short presses to select 25mW/200mW/600mW/800mW 

Channel select

• Select channels by simple short presses.
• Blue LED light stands for CH1, short presses to change 8 channels sequentially.

Band select

• Press button for 2S, Green LED will flash, then short presses to select 5 bands.

Recommended (Not Included)

Recommended capacity: 1050-1500 Mah
Recommended voltage: 4s / 6s

Includes

• 1 x Spare screw pack (include：chamfer m3*8mm 4pcs/m3*12mm 2pcs /M3 anti-loosening nut 2 pcs /m3*30 aluminum pillar 1 pcs/)
• 1 x Foxeer Lollipop3 5.8G Antenna（Black RP-SMA）
• 1 x TCMM-RC Night Phoenix Freestyle Drone
• 1 x 10pcs* black nylon cable tie (25*100mm)
• 1 x 3D printed GOPRO SESSION Mount
• 1 x 2* small wrench (random thickness)
• 2 x TCMMRC Kevlar battery strap
• 4 x  Brushless Motor Nut Cap
• 4 x T5046C 3-blade propeller
• 1 x antenna tube
• 1 x warranty card