NewBeeDrone BeeID V1.1 M10Q GPS Module + Remote ID

The NewBeeDrone BeeID V1.1 M10Q GPS Module with Remote ID & Drone Tracker goes beyond compliance. It's integrated Drone Tracker helps you locate and recover your downed drone using apps like Drone Scanner — no extra hardware needed. With the advanced u-blox M10Q chipset and a high-gain ceramic antenna, the BeeID module locks satellites fast and delivers stable, accurate positioning — perfect for GPS Rescue and autonomous navigation. Remote ID. GPS Accuracy. Drone Recovery. All-in-One.

Note: iNAV Users: Please disable the AUTO-CONFIG setting in iNAV to ensure proper functionality of the BeeID module.

VIDEO: Remote ID & GPS | NewBeeDrone BeeID

• Built-in Drone Tracker using BLE signal
• Supports smartphone-based search apps
• Designed for long-range and freestyle recovery situations
• Improves your chances of successful drone recovery
• Supports GPS / GLONASS / GALILEO
• 72-channel parallel tracking
• Fast lock times and accurate coordinates
• Works with Betaflight, iNAV, Ardupilot, PX4
• High-precision u-blox M10Q GPS
• Built-in Drone Tracker for signal-based drone recovery
• Remote ID compliant for FAA requirements
• Lightweight and compact (approx. 5.2g)
• Ceramic GPS antenna for strong reception
• WiFi setup via phone or PC
• Standard UART interface
• Built-in barometer for Remote ID altitude broadcasting

• Dimensions: 22mm x 15.6mm x 8mm
• GPS Module: M10Q GPS for fast and precise location tracking
• Protocol: GPS L1. GLONASS L1. GALILEO E1.
• Weight:5.2g
• Antenna: Ceramic GPS Antenna
• Receiving Ch: 72ch
• Bitrate: 115200bps
• Speed Accuracy: 0.05m/s
• Dynamic Characteristics: 50,000 meters
• Operating Tempereture: -40°C - +85°C
• Connectivity: WiFi for configuration; BLE for RemoteID broadcasting
• Power: 5V input and ground connection
• Compatibility: Standard GPS UART output; works with Betaflight, iNAV, Ardupilot, and PX4
• Built-in Barometer: Provides altitude data for regions with altitude reporting requirements (The barometer does not participate in the flight, it is used solely for broadcast reports only.） 

BeeID M10Q – GPS + BLUETOOTH SETUP INSTRUCTIONS

Step 1: Verify Flight Controller Compatibility: Before installation, ensure that your flight controller (FC) and its firmware support the UBLOX GPS protocol.

• Some older versions of Betaflight firmware may not be compatible with UBLOX GPS.
• It is recommended to update your FC to the latest firmware to ensure proper functionality.

Step 2: Wiring the BeeID M10Q GPS Module: Proper wiring is essential for accurate data transmission between the BeeID module and your flight controller. Follow these steps:

• Connect the BeeID TX (Transmit) pin to the FC RX (Receive) pin on the same UART port.
• Connect the BeeID RX (Receive) pin to the FC TX (Transmit) pin on the same UART port.
• Ensure 5V power and ground are correctly connected to provide stable operation.

Step 3: Configuring the UART Port: After wiring, configure the corresponding UART port in your flight controller firmware:

• Set the baud rate to 115200bps to match the module’s default speed.
• Enable GPS mode on the selected UART port.
• Save and reboot your flight controller to apply the changes.

Step 4: Confirm GPS Functionality: Verify that the module successfully acquires GPS satellites.

• In Betaflight, iNAV, or Ardupilot, check the GPS status page for satellite lock and position updates.
• Ensure that RemoteID broadcasting is active and functional via BLE. You can use the Drone Scanner App to check the broadcasting information. 

• BeeID 3D File 
• Firmware - Please don't update the firmware if you get the V1.1 version
• FAA UAS Declaration of Compliance here

•  1x NewBeeDrone BeeID v1.1 M10Q GPS Module + Remote ID

Tiny GPS with RemoteID built in! NewBeeDrone BeeID M10Q