The AOS V2 Frame Kit has been designed to deliver the ultimate freestyle flight experience. The unique arm geometry has been refined through topology optimization to deliver maximum strength and stiffness for minimum weight. The same technology is used to optimize aircraft, satellites, and race cars. The new arm geometry provides even more stiffness in key directions as well as improved durability in a front impact. The 3-screw motor mounting reduces weight and removes the motor hole that can be a stress riser for compressive failure.

FROM THE PILOT

"When I set out to create a bind and fly version of the AOS 5 V2 I had the vision to combine the latest and greatest technology into the ultimate FPV freestyle machine. This is the result."

- Chris Rosser, AOS RC

Choose a Size:

• 3.5"
• 5"
• 5.5"

Note: This is the frame kit only. electronics are not included.

VIDEO: AOS 5 V2 FPV Frame: Better than the Apex DC? No props in view; no compromises!

• Choose from 3.5", 5". or 5.5" Arm Size
• Topology-optimized truss design arms
• 2.5mm Top and Bottom Plates
• Optimized Camera Protection
• Designed for Low Vibration
• 32x32 GoPro Mounting
• Durable Carbon Fiber
• Built by iFlight

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

AOS V2 3.5" FRAME KIT

• One 25.5x25.5 or 20x20 mm stack in the front and one 25.5x25.5 or 20x20 mm stack in the rear OR
• Fits both 20mm (DJI camera) and 19mm (Micro-sized) cameras
• Motor mounting 9x9 up to 12x12 (1404, 1505 recommended)
• One 30.5x30.5, 25.5x25.5, or 20x20 mm stack in the centre
• Fits the Caddx Vista or HDZero 1W Freestyle VTX perfectly
• Standoffs, frame, and motor screws included
• Designed for up to 3.5-inch props
• Approx. 40g with all hardware
• 4 mm Arms

AOS V2 5" FRAME KIT

• 32x32mm GoPro mounting holes in THE top plate with installed press nuts
• Fits the DJI Air Unit (use front stack mounting) and HDZero 1W VTX
• Up to three 30.5x30.5 mm 25.5x25.5 mm or 20x20 mm stacks
• Designed for up to 5.1-inch props (no props in view)
• Recommended motor size 2306, 2207, 2208, 25mm
• Fits the DJI FPV camera or 19x19 mm camera
• 16x16 mm up to 19x19 mm motor mounting
• 2mm Top Plate and Sandwich Plates
• Approx. 115g with all hardware
• XT60 pass through in top plate
• Two captive battery strap slots
• 2.5mm Bottom Plate
• 6 mm Arms

AOS V2 5.5" FRAME KIT

• 32x32mm GoPro mounting holes in the top plate with installed press nuts
• Fits the DJI Air Unit (use front stack mounting) and HDZero 1W VTX
• Up to three 30.5x30.5 mm 25.5x25.5 mm or 20x20 mm stacks
• Designed for up to 5.5-inch props (no props in view)
• Recommended motor size 2207, 2208, 25mm
• Fits the DJI FPV camera or 19x19 mm camera
• 16x16 mm up to 19x19 mm motor mounting
• 2mm Top Plate and Sandwich Plates
• Approx. 125g with all hardware
• XT60 pass through in top plate
• Two captive battery strap slots
• 2.5mm Bottom Plate
• 6 mm Arms

IMPORTANT NOTES

• Insert important warnings or notes here. Example: "Do not overheat." or "Always use the included charger for best performance."

• iFlight Nazgul F5 5x3.5x3 3-Blade 5.1" Propeller (Set of 4) (for AOS 5)
• Caddx DJI Digital HD FPV Air Unit Kit

•   (Insert links such as manuals, firmware, etc)

• 4x AOS RC V2 Arm (Choose Size)
• 2x AOS RC V2 Camera Plate
• 1x AOS RC V2 Bottom Plate
• 1x AOS RC V2 X Plate Kit
• 1x AOS RC V2 Top plate
• 2x iFlight LiPo Strap
• 1x Hardware Kit
• 2x Battery Pad

ADD VIDEO TITLE HERE IN BOLD CAPS

ADD VIDEO TITLE HERE IN BOLD CAPS