The MATEKSYS F405-VTOL Flight Controller features 25x25 and 35x35 mounting patterns and weighs 25g. It features a Barometer, BlackBox MicroSD, 6x UARTS, 4x ADC, 12x PWM outputs, 2x PINIO (Camera switch, P101 pad), PDB for 5x individual ESC/Motors, 6.8-30V DC IN (2-6S LiPo), 220A High-precision current sensor, BEC 5V 2A for FC and peripherals, BEC 9V 2A (12V options for Camera/VTX), BEC VX 8A cont. 10A Peak for servos.

Note: (Insert any product notes here in Red BOLD Italic. Example: "First Shipment expected January 2022" or "Electronics are Not Included".)

VIDEO: (Insert Video Title here in Bold)

• BEC VX 8A cont. 10A Peak for servos (5V,6V,7.2V option)
• BEC 9V 2A, 12V option for Camera/VTX
• 2x PINIO (Camera switch, P101 pad)
• 25x25 and 35x35 mounting patterns
• 220A High-precision current sense
• BEC 5V 2A for FC and peripherals
• PDB for 5x individual ESC/Motors
• 6.8-30V DC IN (2-6S LiPo)
• MCU STM32F405RGT6
• Barometer SPL06-001
• BlackBox MicroSD
• 12x PWM outputs
• IMU ICM42688-P
• OSD AT7456E
• 6x UARTS
• 4x ADC

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

• Mounting: 25 x 25mm-Φ2mm, 35 x 35mm- Φ4mm
• Built in inverter on UART2-RX for SBUS input
• MCU: STM32F405RGT6, 168MHz , 1MB Flash
• USB/Beep Extender with Type-C(USB2.0)
• 6x UARTs, 1x Softserial_Tx option(INAV)
• 4x ADC (VBAT, Current, RSSI, Airspeed)
• Weight: 25g w/ USB/buzzer adapter
• Switchable Dual Camera Input
• 1x spare PINIOOSD: AT7456E
• Dimensions: 45 x 42 x 15mm
• Blackbox: MicroSD card slot
• 12x PWM outputs
• IMU: ICM42688-P
• Baro: SPL06-001
• 1x I2C

FC Firmware

• INAV: MATEKF405TE_SD (INAV 5.0 or newer)
• ArduPilot: MatekF405-TE

PDB

• Battery Voltage divider 1K:20K (Scale 2100 in INAV, BATT_VOLT_MULT 21.0 in ArduPilot)
• Support continuous load of up to 30A & peak of 50A on each ESC pad of Quadcopter
• Support continuous load of up to 100A on ESC pad near the current sensor resistor
• Current Senor: 220A, 3.3V ADC (Scale 150 in INAV, 66.7 A/V in ArduPilot)
• Sense resistor: 100A continuous, 220A peak
• 5x ESC power pads, total 100A continuous
• Input voltage range: 6.8~30V (2~6S LiPo)

BEC 5V output

• Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
• Continuous current: 2 Amps

BEC 9V /12V output

• For stable 9V/12V output, input voltage should > output voltage +1V
• Designed for Video Transmitter, Camera, Gimbal ect
• Continuous current: 2 Amps
• 12V option with Jumper pad

BEC Vx output

• for stable Vx output, input voltage should > Vx voltage +1V
• Voltage adjustable, 5V Default, 6V or 7.2V via jumper
• Continuous current: 8 Amps, 10A Peak
• Designed for Servos

BEC 3.3V output

• Designed for Baro / Compass module and external 3.3V peripherals
• Continuous current: 200mA
• Linear Regulator
  
  

IMPORTANT NOTES

• Board is shipped unsoldered.

•  (Insert recommended products here. Example: "Battery: Lumenier 10000mAh 6s 25c Lipo Battery")

• Firmware

• 1x USB(Type-C)/Beep (Passive buzzer) Extender + 20cm JST-SH-6P to JST-SH-6P cable for USB extender.
• 1x 20cm JST-GH-4P to JST-GH-4P cable for I2C port
• 1x MATEKSYS F405-VTOL Flight Controller
• 1x Rubycon ZLH 35V 470uF capacitor

ADD VIDEO TITLE HERE IN BOLD CAPS

ADD VIDEO TITLE HERE IN BOLD CAPS