What if you could get the combined MCU speed and ESC power of a big stack, but carefully arranged on a 25x25 whoop size board? That would be crazy right? Well, iFlight just did it...

This is the new iFlight BLITZ series AIO FC for your ultimate build. A future-proof all-in-one FC will step up the game and make more room for future flight firmware development like Betaflight, Emuflight, etc. Featuring an F745 FC and 55A ESC. Lightweight, minimum size, minimum work. This could only be achieved using BGA chipsets instead of ordinary QFP (big size) MCUs and ultra-powerful Mosfets for almost any build. Solder your motor wires on and let's go! DJI Plug&Play plug and so many UARTs most people wouldn't even use them all. Compatible with digital and analog FPV, onboard Barometer for possible long-range flights, and much more. Unleash the beast!

Note: (Insert any product notes here in Red BOLD Italic. Example: "First Shipment expected January 2022" or "Electronics are Not Included".)

VIDEO: Diatone Mamba H743 MK4 FC & 128K ESC Unboxing

• Vista digital system Plug-and-Play (VBAT passthrough)
• MCU: BGA-STM32F745, 216MHz
• Blackbox: 16MB Onboard Flash
• OSD: AT7456E

WIRING SUGGESTIONS

• UART1/4/7 for GPS or other sensors that require a serial port
• UART2 for VTX HD/Analog Telemetry
• UART3 for Receiver

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

IFLIGHT BLITZ F745 FC

• Mounting pattern: 25.5*25.5mm φ3mm
• FC Firmware: IFLIGHT_F745_AIO
• Blackbox: 16MB Onboard Flash
• OSD: IFLIGHT OSD (AT745E）
• ESC Firmware: G-H-50 BLS
• Dimensions: 32.5*32.5mm
• MCU: BGA-STM32F745
• Connector: Micro-USB
• BEC output: 5V 2.5A
• Barometer: DPS310
• Weight: 8.5g

IFLIGHT BLITZ 55A 2-6S ESC

• Mounting pattern: 25.5*25.5mm/Φ3mm
• Constant: 55A / Burst: 60A
• ESC Firmware: G-H-30 BLS
• Dimensions: 32.5*32.5mm
• Current Sensor: Yes
• Current sensor：Yes
• Current scale: 100
• ESC MCU：8BB21
• Input: 2-6S LIPO
• BLHeli: BLHeli-S
• Telemetry: No
• Uarts: 5

(INSERT VTX TITLE HERE IN BOLD CAPS)

IMPORTANT NOTES

• The DJI plug&play port has no voltage regulator (BEC) and is passing through VBAT. The Caddx Vista goes up to 26.4V (6S), the DJI Air Unit goes up to 17.6V (4S). Make sure not to plug-in your DJI Air Unit directly when you're flying 6S, because this would fry it! BEC to add for your 6S build can be found here: https://shop.iflight-rc.com/index.php?route=product/product&product_id=747
• Small motor 4S builds should usually need an additional capacitor of at least 16V/220uF, for 6S go up to 35V or even 50V. Bigger motors have a bigger current draw, higher voltage spikes and more serious back EMF (motor braking, works like a generator). Make sure to add big enough or even bigger low ESR capacitors on the AIO battery pad or on your battery lead the more aggressive motors you fly. There's a choice of capacitors in the package, but it's never a bad idea to make sure to protect your board. Smaller boards have less capacitance which has to be covered with external capacitors, there's no way around.

•  (Insert recommended products here. Example: "Battery: Lumenier 10000mAh 6s 25c Lipo Battery")

•   (Insert links such as manuals, firmware, etc)

• 1x iFlight BLITZ F7 V2 AIO Board - F745 FC + 55A 2-6S BLHeli_S ESC
• 8x 0.8mm black Heat shrink tube 10mm
• 1x XT60 16AWG cable 100mm
• 1x XT30U 18AWG cable 70mm
• 1x 1.0-7P cable 50mm-28mm
• 8x M2 Transparent Nylon Nut 
• 2x Capacitor 470uF/35V
• 4x M2 silicon grommets
• 1x 1.0-7P cable 50mm
• 8x M2 12mm screws

ADD VIDEO TITLE HERE IN BOLD CAPS

ADD VIDEO TITLE HERE IN BOLD CAPS