The Holybro Pixhawk 6X FC Module is the latest update to the successful family of Holybro's Pixhawk flight controllers. It is based on the Pixhawk® FMUv6X Open Standard and the Pixhawk® Autopilot Bus Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk® 6X, you can find a STMicroelectronics® based STM32H753, paired with sensor technology from Bosch®, and InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.

Note: (Insert any product notes here in Red BOLD Italic. Example: "First Shipment expected January 2022" or "Electronics are Not Included".)

VIDEO: Diatone Mamba H743 MK4 FC & 128K ESC Unboxing

• Flight Controller Module for the Holybro Pixhawk 6X
• PX4 Autopilot® pre-installed

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

• Operating temperature: -40 ~ 85°c
• Dimensions: 38.8 x 31.8 x 14.6mm
• Weight: 23g

PROCESSORS AND SENSORS

• FMU Processor: STM32H753
  
  • 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
• IO Processor: STM32F103
  
  • 32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM
• On-board sensors
  
  • Accel/Gyro: ICM-20649 or BMI088
  • Accel/Gyro: ICM-42688-P
  • Accel/Gyro: ICM-42670-P
  • Mag: BMM150
  • Barometer: 2x BMP388

ELECTRICAL DATA

• Voltage Ratings:
  
  • Max input voltage: 6V
  • USB Power Input: 4.75~5.25V
  • Servo Rail Input: 0~36V
• Current Ratings:
  
  • Telem1 output current limiter: 1.5A
  • All other port combined output current limiter: 1.5A

MECHANICAL DATA

• Dimensions
  
  • Flight Controller Module: 38.8 x 31.8 x 14.6mm
  • Standard Baseboard: 52.4 x 103.4 x 16.7mm
  • Mini Baseboard: 43.4 x 72.8 x 14.2 mm
• Weight
  
  • Flight Controller Module: 23g
  • Standard Baseboard: 51g
  • Mini Baseboard: 26.5g

INTERFACES

• 16- PWM servo outputs
• R/C input for Spektrum / DSM
• Dedicated R/C input for PPM and S.Bus input
• Dedicated analog / PWM RSSI input and S.Bus output
• 4 general-purpose serial ports
  
  • 3 with full flow control
  • 1 with separate 1.5A current limit (Telem1)
  • 1 with I2C and additional GPIO line for external NFC reader
• 2 GPS ports
  
  • 1 full GPS plus Safety Switch Port
  • 1 basic GPS port
• 1 I2C port
• 1 Ethernet port
  
  • Transformerless Applications
  • 100Mbps
• 1 SPI bus
  
  • 2 chip select lines
  • 2 data-ready lines
  • 1 SPI SYNC line
  • 1 SPI reset line
• 2 CAN Buses for CAN peripheral
  
  • CAN Bus has individual silent controls or ESC RX-MUX control
• 2 Power input ports with SMBus
  
  • 1 AD & IO port
  • 2 additional analog input
  • 1 PWM/Capture input
  • 2 Dedicated debug and GPIO lines

(INSERT ESC TITLE HERE IN BOLD CAPS)

(INSERT VTX TITLE HERE IN BOLD CAPS)

IMPORTANT NOTES

• Note: This is the replacement Flight Controller Module for the Holydbro Pixhawk 6X Flight Controller

•  (Insert recommended products here. Example: "Battery: Lumenier 10000mAh 6s 25c Lipo Battery")

• All technical specifications of the complete Holybro Pixhawk 6X
• Supported Firmware 

• 1x Holybro Pixhawk 6X FC Module

ADD VIDEO TITLE HERE IN BOLD CAPS

ADD VIDEO TITLE HERE IN BOLD CAPS