BetaFPV F4 1S 12A AIO Brushless Flight Controller - ELRS 2.4G V2.0

BetaFPV F4 1S 12A AIO Brushless Flight Controller - ELRS 2.4G V2.0

Out of Stock

Only left for same day shipping. Order now!
Earn
Notify me when this product is in stock
BetaFPV F4 1S 12A AIO Brushless Flight Controller - ELRS 2.4G V2.0
 If you want to try a bigger FPV drone than 65mm/75mm on 1S power, and still want smooth and powerful flying actions, this 12A  AIO FC V2  ELRS is definitely your best choice!
Share

About this product

BETAFPV has come up with their F4 1S 12A AIO Flight Controller which is suitable for 3" lightweight builds and toothpick drones like the HX115 SE Toothpick Drone. If you want to try a bigger FPV drone than 65mm/75mm on 1S power, and still want smooth and powerful flying actions, this 12A  AIO FC V2  ELRS is definitely your best choice!

Features

  • F4 1S 12A AIO Flight Controller is the best choice for building ultra-lightweight 3" toothpick drones like HX115 SE FPV Quad.
  • Most of the 1S flight controllers on the market come with 5A ESC by now, but this FC especially integrates 1S 12A ESC, it can provide more sufficient power for 3" toothpick drones.
  • Built-in current meter, 2 programmable RGB LEDs, and SPI Frsky receiver. At the same time, all the pads are left for the external receivers with UART1 and UART2, for buzzers, etc.
  • Whoop mounting hole pattern, be compatible with most 1S 3" frame. Large pads are reserved for solder motor cables, this design will make solder easier.

Specifications

  • Item: F4 1S 12A V2 AIO FC (ELRS)
  • Weight: 4.74 g (without power cable and BT2.0 connector)
  • CPU: STM32F411CEU6 (100MHZ )
  • Six-Axis: MPU6000 (SPI connection)
  • Firmware version: betaflight_4.2.0_STM32F411
  • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
  • Receiver: ELRS
  • Motor Pin Connecter: 1.25mm Header Pins
  • Mounting Hole Size: 26mm x 26mm 
  • USB Port: Type-C, SH1.0 4-Pin

1S 12A ESC

  • Built-in ESC with 12A continuous and peak 25A current
  • Input voltage: 1S-2S
  • ESC firmware: Z_H_30_REV16_7.HEX
  • Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM

This new BLHeli_S firmware (named Z_H_30_REV16_7.HEX) is supported by BLHeli Configurator, BLHeliSuite, and Bluejay Configurator.

Below is the Diagram for ELRS 2.4G V2.0 Board

Recommend Parts (Not Included)

Includes

  • 1 x F4 1S 12A AIO FC ELRS 2.4G V2.0 
  • 4 x Anti-vibration rubber dampers
  • 4 x M2 x 10mm screws
  • 4 x M2 x 10mm screws
  • 8 x M2 screw nut
  • 1 x BETAFPV dipole T antenna (2.4G/46mm, only for ELRS RX version board)
  • 8 x PH-1.25 connector for motor (not soldered, only for ELRS RX version board)

FPV Regulatory Notice

The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your area. It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. GetFPV cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.

More Information

SKU 17836
UPC (GTIN) 764613343014
Manufacturer BETAFPV
NDAA Compliant No
Mounting Pattern 25.5x25.5mm
Item Returns This item can be returned

Also Purchased