SpeedyBee F405 V5 Stack - F405 FC + 55A 3-6S OX32 ESC - 30x30 - Deluxe

The SpeedyBee F405 V5 Stack - F405 FC + 55A 3-6S OX32 ESC - 30x30 - Deluxe features an upgraded F405 flight controller and OX32 ESC. The Deluxe edition includes a bunch of extras to simplify working with this stack. With the built-in Bluetooth chip, use Betaflight to tune in the field. With a built-in barometer and connectivity to all DJI Air Units, along with UART ports for maximum customizability, this stack was crafted with precision - your all-in-one choice for top performance.

• Deluxe Edition comes with Soldering Practice Board, Power Expansion Board, USB Extension, and Smart Short-Circuit Protection Tool
• New clock sync function improves detection accuracy
• Easier soldering with added direct sockets for GPS and receiver
• Nickel-plated bus bars
• Double-sided heat-spreading
• Wireless tuning and upgrading

F405 FC

• MCU: STM32F405
• IMU (Gyro): ICM42688P
•  USB Port Type: Type-C
• Barometer: SPA06-003
• OSD Chip: AT7456E
• Bluetooth Tuning: Supported. Connect via SpeedyBee App for FC firmware flashing and parameter tuning
• Wireless FC Firmware Upgrade: Supported
• DJI Air Unit Connection: Supports 6-pin direct plug-in or solder connection
• Blackbox: Supported, built-in 16MB storage chip
• Input Voltage: 3-6S LiPo Battery
• 5V BEC Output: 9 groups (4x +5V pads, 1x BZ+ buzzer pad, and 4x 5V pads at corners for LEDs
• 9V BEC Output: 2 groups (1x 9V pad on front, 1x 9V pad on back). Supports PINIO remote on/off control
• MCU & Gyro Power: Independent LDO
• 3.3V Output: 1 group (1x 3.3V pad on front)
• 4.5V Output: 3 groups (3x 4.5V pads on front) Can power receiver & GPS when FC is powered via USB. Max current 1A.
• ESC Signal: M1-M4 pads and 10-pin connector on back
• Servo Signal: S5-S6 pads on the front
• ESC Telemetry Input: Supported (UART 5)
• Betaflight Camera Tuning Pad: Supported (CC pad on front)
• I2C: Supported (GPS connector + pads)
• UART
  • UART1: Bluetooth
  • UART2: front pads for receiver
  • UART3: DJI VTX pads + 6-pin SH1.0
  • UART4: GPS pads + front 6-pin SH1.0
  • UART5: TLM
  • UART6: receiver pads + rear 4-pin SH1.0
• ST LED Pads: Supported, on front G/5V/LED
• Meteor LED Strip Pads: Supported
• Buzzer Pads: Supported
• BOOT  Button: A: Hold BOOT while powering on to force DFU mode for flashing. B: When powered and in standby, short=press cycles LED display modes; long press switches SB-LED/ST-LED. 
• RSSI Pads: Supported
• Smart Port: Not Supported
• Supported FC Firmware: Betaflight
• Firmware Target Name: SPEEDYBEEF405V5
• Factory Firmware Version: Betaflight 4.5.2
• Configurator Version: Betaflight 10.10.0
• Mounting Holes: 30.5 x 30.5 mm (⌀4mm) side opening
• Dimensions: 39mm x 39mm x 4.9mm (LxWxH)
• Weight: 8.1g

55A 3-6S OX32 ESC - 30x30

• Default Firmware: OX32
• Continuous Current: 55A (per channel) / 220A (4-in-1)
• Maximum Current: 70A (per channel) / 280 (4-in-1)
• TVS Protective Diode: Yes (built-in)
• External Capacitor: 1000µF Solid Capacitor
• ESC/Motor Protocol: DSHOT300/600
• Input Voltage: 3-6S Lipo
• Power Output: VBAT
• Current Sensor: Supported
• ESC Telemetry: Supported
• Mounting Holes:  30.5 x 30.5 mm (⌀4mm) side opening
• Dimensions: 40.9mm x 44.9mm x 8mm (LxWxH) 

•  ESC Webpage

• 1x SpeedyBee F405 FC
• 1x SpeedyBee 55A 3-6S OX32 ESC
• 1x Soldering Practice Board
• 1x Short-Circuit Protection Tool
• 1x Active Buzzer
• 4x Power Expansion Boards
• 1x Buzzer Red & Black Wires 100mm
• 1x Type-C Extension Module
• 1x 1000uf/35V Capacitor
• 1x XT60 120mm Connector
• 2x Capacitor Heat Shrink Tube
• 4x M3 Stack Mounting Bolts 30mm
• 5x M3 Hex Nylon Nuts
• 5x M3 Black Silicon Washers
• 5x M2 Anti Vibration Silicone Grommets
• 5x M3 Anti Vibration Silicone Grommets
• 1x 25mm 10-Pin SH1.0
• 1x 75mm 10-Pin SH1.0
• 1x 80mm 6-Pin SH1.0
• 1x 120mm 6-Pin SH1.0
• 1x 120mm 6-Pin SH1.0 to 4-Pin SH1.0
• 1x 100mm 4-Pin SH1.0
• 1x Quickstart Guide