MATEKSYS AP Periph Adapter Node - CAN-G474

The MATEKSYS CAN-G474 enhances drone communication with its high-speed 5 Mbit/s CAN transceiver and STM32G474 MCU, built on ArduPilot's AP_Periph firmware. It supports seamless integration of ArduPilot peripherals like GNSS, Compass, Barometer, and Rangefinders into DroneCAN systems, as well as GPIO-based devices such as PWM and LED notify modules, offering a simple solution for expanding drone functionality.

Note: (Insert any product notes here in Red BOLD Italic. Example: "First Shipment expected January 2022" or "Electronics are Not Included".)

VIDEO: (Insert Video Title here in Bold)

• ArduPilot Driver Library Compatibility
• ArduPilot AP_Periph Firmware
• 5 Mbit/s CAN Transceiver
• STM32G474 MCU
• CANFD Capability

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

• UART1 (TX1, RX1): supports firmware updates in DFU mode
• ST debug: SWC & SWD (on the bottom side)
• CAN transceiver: Data rates up to 5 Mbit/s
• Input voltage range: 4.55.5V @5V pad/pin
• MCU: STM32G474CE, 512KB Flash
• Operating temperature: -3085°C
• Power consumption: 62mA
• CAN bus: 2x
• UARTs: 4X
  
  • Supports GNSS, Compass, and Barometer sensors over MSP protocol. MSP is enabled on TX3 by default
  • For peripheral GNSS, Rangefinder, Proximity, EFI, RC input (receiver)
• SPI: 1x
  • SPI pads for RM3100 are on the bottom side, with “CS, MOSI, MISO, SCK” silk print
  • For peripheral RM3100
• I2C bus: 2x
  
  • For peripheral I2C Airspeed sensor, Barometer, Compass
• PWM outputs: 11x
  • For Servos and ESC; all PWMs support DMA/DShot
  • PWM11 pad is on the bottom side, with an “11” silkprint
  • PWM1-10 on DuPont 2.54mm holes

PHYSICAL

• 5x JST-GH-4P (SM04B-GHS-TB): CAN1, CAN2, I2C1, UART1, and UART4
• 1x JST-GH-6P (SM06B-GHS-TB):UART3 + I2C2
• Board size: 36mm x 36mm x 6mm, 5.2g
• Mounting: 30.5mm, 4x Dia. 3mm
• Holes: 18x DuPont 2.54mm hole

LED

• Blue, Slow blinking: Communicating with the flight controller
• Blue, Fast blinking: Booting
• Red: 3.3V indicator

IMPORTANT NOTES

• Insert important warnings or notes here. Example: "Do not overheat." or "Always use the included charger for best performance."

•  (Insert recommended products here. Example: "Battery: Lumenier 10000mAh 6s 25c Lipo Battery")

• ArduPilot AP_Periph Manual for peripheral Sensors
• ArduPilot AP_Periph Manual for DroneCAN Output

• 1x MATEKSYS AP Periph Adapter Node - CAN-G474
• 2x JST-GH-4P to JST-GH-4P 20cm silicon wire
• 1x JST-GH-6P to JST-GH-6P 20cm silicon wire

ADD VIDEO TITLE HERE IN BOLD CAPS

ADD VIDEO TITLE HERE IN BOLD CAPS