Lumenier RID - Remote ID Module

Lumenier RID - Remote ID Module

Back Ordered

Only left for same day shipping. Order now!
Earn
Lumenier RID - Remote ID Module
The Lumenier RID complies with FAA remote ID regulations and features an integrated UBLOX SAM-M10Q and magnetometer for precise positioning in a compact and lightweight design.

About this product

Note: The next batch shipment estimate is June 2024.

The Lumenier RID complies with FAA regulations and features an integrated UBLOX SAM-M10Q for precise positioning. Its Bluetooth 4 and 5 broadcast transmitter and reverse polarity protection ensure seamless connectivity and safety. Equipped with an onboard magnetometer, efficient power design, and a red/green LED status indicator, it offers reliable performance for drone enthusiasts and professionals alike. The GPS and magnetometer data can be used at the same time by a flight controller for autopilot functionality and OSD information. Each module is individually tested and verified and includes a test report.

VIDEO: (Insert Video Title here in Bold)

Features

  • Bluetooth 4 and 5 broadcast transmitter module with integrated antenna
  • The onboard connector uses “Basic GPS” pinout from Pixhawk standard
  • Functions as a GPS/Mag data source as well for the Flight Controller
  • Efficient power design with a wide voltage range of 5-34V (2s-8s)
  • Integrated UBLOX SAM-M10Q GPS
  • Meets FAA remote ID requirements
  • 3.3V Logic levels – ESD-protected
  • Onboard LIS3MDL magnetometer
  • Red/Green LED status indicator
  • Individual test report included
  • Reverse Polarity Protection

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

Specifications

  • Broadcast Transmitter Module: Bluetooth 4 and 5 (with integrated antenna)
  • GPS: Integrated UBLOX SAM-M10Q
  • Onboard Magnetometer: LIS3MDL
  • Logic Levels: 3.3V (ESD-protected)
  • Magnetometer I2C Address: 0x1E
  • Reverse Polarity Protection: Yes
  • Voltage Range: 5-34V (2-8S)
  • Lightweight 9g
  • Size: 32.5x16.5x10.5mm

IMPORTANT NOTES

  • Onboard connector uses “Basic GPS” pinout from Pixhawk standard
  • Red/Green LED status indicator 
    • Flashes RED on boot until a fix is detected, then flashes green.
    • The RID Bluetooth functionality is still active without a fix; it just sends “unknown location” data. 
  • Use Caution. If the board is not in heat shrink and sits on a conductive surface across these two points, it will short out the battery and could cause damage.

Recommended (Not Included)

Lumenier RID - Remote ID + Antenna Rear Mount
$7.99
NEW
Lumenier RID - Remote ID Universal Screw Mount
$6.99
NEW
Lumenier RID - Remote ID Strap Mount
$6.99
NEW

Includes

  • 1x Lumenier RID Remote ID Module
  • 1x FAA UAS ID QR Code Sticker  
  • 1x Test Report Receipt Sticker 
  • 1x GH 6-pin to GH 6-pin 
  • 1x GH 6-pin to SH 6-pin 
  • 1x GH 6-pin to Pigtail 
  • 1x Heat Shrink
 

More Information

SKU 22003
UPC (GTIN) 724376355242
Manufacturer Lumenier
NDAA Compliant No
Expected Date 2024-06-10
Item Returns This item can be returned

Also Purchased

Flite Test FT EZ ID - Remote ID Module
$99.99
NEW
Holybro Remote ID /w Case
$29.99
NEW
Holybro Remote ID Module - No Case
$19.99
NEW
Dronetag Beacon V2 Broadcast Remote Identification Device
$219.00
NEW