Lumenier LUX H743 Flight Controller - NDAA
$148.99
Back Ordered
Only left for same day shipping. Order now!
Lumenier LUX H743 Flight Controller - NDAA
The Lumenier LUX H743 – NDAA Flight Controller features some of the latest sensors in drone technology, including the next-generation InvenSense ICM-45686 Gyro/Accelerometer, Infineon DPS368 barometer, and STMicroelectronics LIS2MDL magnetometer.
NDAA Compliant Product
About this product
The Lumenier LUX H743 – NDAA Flight Controller features some of the latest sensors in drone technology, including the next-generation InvenSense ICM-45686 Gyro/Accelerometer, Infineon DPS368 barometer, and STMicroelectronics LIS2MDL magnetometer. Additionally, the LUX H743–NDAA features several differentiating characteristics, including a camera feed switch that allows toggling between two independent video streams.
VIDEO: NDAA Compliant 8s Stack for FPV Drone Builds: Lumenier Lux FC & Siege ESC
Features
- Dual Gyro/Accelerometer Sensors with Synchronization Clock Signal and Independent Power Supplies
- Supported Firmware - Betaflight, INAV, Ardupilot, and PX4
- 7 UART Ports, Including 2 UARTs with Flow Control
- Internal Magnetometer
- NDAA Compliant
- LED supported
Specifications
- Input Voltage: 3S to 8S
- MCU: ST STM32H743, ARM® Cortex®- M7, 480MHz, 1MB RAM, 2MB Flash
- Gyro/Accelerometer #1: Invensense ICM-45686
- Gyro/Accelerometer #2: Invensense ICM-42688-P
- Barometer: Infineon DPS368
- Magnetometer: STMicroelectronics LIS2MDL
- Flash Storage: Windbond W25Q128JV (128Mbit)
- OSD: AT7456E
- Size: 37.5mm x 37.5mm
- Mounting holes: 30.5mm x 30.5mm
- External Sensors: I2C Ports
- CANbus Support: PX4 and Ardupilot only
- LED Strip Control: WS2812
- Voltage regulators: +5V Regulator for Accessories, +10V Regulator for VTX Power
- Camera Control Output: Supported
- Dual Camera Switch: Supported
- VTX Power Switch: Supported
- RX PPM Input: Supported
- Analog Battery Sensor Input: 8S and 12S Inputs
- Analog Current Sensor Input: Supported
- Blackbox Storage: SD Card and Flash
- USB: Type-C (2.0)
- Pixhawk Telemetry: GPS and CAN Ports
IMPORTANT NOTES:
- When using Ardupilot or PX4 builds, an SD card is required to boot after firmware installation.
Links
MANUAL
NDAA DECLARATION
FIRMWARE
- PX4:
- INAV:
- Betaflight:
- Ardupilot:
Includes
- 1x Lumenier LUX H743 Flight Controller - NDAA
- 1x 100mm 8-pin JST-GH to 8-pin JST-GH Cable
- 1x 100mm 8-pin JST-GH to 8-pin JST-SH Cable
- 1x 200mm 4-pin JST-GH to 4-pin JST-GH Cable
- 1x 200mm 6-pin JST-GH to 4-pin X1002H Cable
- 1x 200mm 6-pin JST-GH to 6-pin JST-GH Cable
- 5x M3 Rubber Grommets
More Information
| SKU | G23448US1Z |
|---|---|
| UPC (GTIN) | 723326376771 |
| Manufacturer | Lumenier |
| Country of Manufacture | United States |
| NDAA Compliant | Yes |
| Mounting Pattern | 30.5x30.5mm |
| Flight Controller Processor | H7 |
| Flight Controller Firmware Targets | Betaflight/INAV/Ardupilot/PX4 |
| Gyro | ICM42688P |