iFlight SucceX-D Mini Stack - F7 TwinG V1.1 FC + 45A 2-6S BL32 4-in-1 V1.0 ESC
iFlight SucceX-D Mini Stack - F7 TwinG V1.1 FC + 45A 2-6S BL32 4-in-1 V1.0 ESC
Out of Stock
About this product
The SucceX-D Mini F7 is designed to work seamlessly with the new DJI Digital HD FPV Air Unit.
To make things easier, the DJI Digital HD FPV Air Unit can just be plugged into the FC with the included wire harness. In addition, iFlight added the popular and reliable USB Type-C instead of the Micro USB. Therefore, this stack has the same standard as your DJI module, but the real magic of this flight controller lies in its Twin Gyro configuration.
The TwinG uses two identical Gyros which are oriented side by side with one offset 90 degrees from the other. Betaflight uses GYRO FUSION to blend and average the information from both gyros to send a much cleaner signal to the PID loop controller! Less noise and fewer oscillations across the throttle band without adding any delay! Betaflight software filters can be lowered in most cases as well, which brings a significant decrease in delay.
With plenty of processing power and UARTS, this is also the perfect stack for long-range GPS builds, and the TwinG configuration makes it the perfect FC for builds like micro quads, cinematic filming rigs, and X-Class racers!
Specifications
SucceX-D Mini F7 Flight Controller
- MCU: 216MHz STM32F722
- Gyro：2x ICM20689
- Blackbox：32MB
- Betaflight OSD: YES
- BEC: 5V 2.5A / 9V 2.5A
- Current sensor scale: 100
- Inverter for SBUS input (UART2-RX)
- Smart audio & Tramp VTX protocol supported
- Beeper pad: Yes
- RSSI input pad: No
- UARTs：5
- Motor outputs: 4
- 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)
- 6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V)
- BLHeli32 Telemetry：RX5
- Input voltage：recommended 2-6S, MAX 8S
- Firmware: IFLIGHT_IFF7_TWIN_G(IFRC)
- Mounting pattern: 20*20mm φ3
- Dimensions: 29*29mm
- USB Type-C
SucceX 40A ESC
- MCU: STM32F051K66
- Up to 48kHz PWM frequency
- Capacity: 470uF/50V
- Current Sensor: Yes
- Input: recommended 2-6S
- Constant: 40A / Burst: 50A
- BlHeli32 telemetry: Yes
- Supports up to Dshot1200, Proshot, Oneshot, Multishot
- Target: iFlight-BL32-4IN1
- Weight: 7.2g
- Mounting pattern: 20*20mm φ3mm with Grommets φ2mm
- Dimensions: 31*31mm (including the power pads)
Includes
- 1 x SucceX-D F7 Mini TwinG Flight Controller
- 1 x SucceX Mini 40A 4in1
The SucceX-D Mini F7 is designed to work seamlessly with the new DJI Digital HD FPV Air Unit.
To make things easier, the DJI Digital HD FPV Air Unit can just be plugged into the FC with the included wire harness. In addition, iFlight added the popular and reliable USB Type-C instead of the Micro USB. Therefore, this stack has the same standard as your DJI module, but the real magic of this flight controller lies in its Twin Gyro configuration.
The TwinG uses two identical Gyros which are oriented side by side with one offset 90 degrees from the other. Betaflight uses GYRO FUSION to blend and average the information from both gyros to send a much cleaner signal to the PID loop controller! Less noise and fewer oscillations across the throttle band without adding any delay! Betaflight software filters can be lowered in most cases as well, which brings a significant decrease in delay.
With plenty of processing power and UARTS, this is also the perfect stack for long-range GPS builds, and the TwinG configuration makes it the perfect FC for builds like micro quads, cinematic filming rigs, and X-Class racers!
Specifications
SucceX-D Mini F7 Flight Controller V1.1
- MCU: 216MHz STM32F722
- Gyro：2x ICM20689
- Blackbox：32MB
- Betaflight OSD: YES
- BEC: 5V 2.5A / 9V 2.5A
- Current sensor scale: 100
- Inverter for SBUS input (UART2-RX)
- Smart audio & Tramp VTX protocol supported
- Beeper pad: Yes
- RSSI input pad: No
- UARTs：5
- Motor outputs: 4
- 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)
- 6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V)
- BLHeli32 Telemetry：Yes
- Input voltage：Recommended 2-6S, MAX 6S
- Firmware: IFLIGHT_F722_TWING (IFRC)
- Mounting pattern: 20*20mm φ3
- Dimensions: 29*29mm
- USB Type-C
- SKU: FC07526
SucceX Mini 45A ESC V1.0
- MCU: TM32F051K66
- Up to 48kHz PWM frequency
- Capacity: 470uF/50V
- Current Sensor: Yes
- Input: recommended 2-6S
- Constant: 45A / Burst: 55A
- BlHeli32 telemetry: Yes
- Supports up to Dshot1200, Proshot, Oneshot, Multishot
- Firmware: iFlight-G071-4IN1
- Weight: 7.2g
- Mounting pattern: 20*20mm φ3mm with Grommets φ2mm
- Dimensions: 31*31mm (including the power pads)
- SKU: SE09879
Includes
- 1 x SucceX-D F7 Mini TwinG V1.1 Flight Controller
- 1 x SucceX Mini 45A 4in1 V1.0 ESC
- 1x XT60H-M 14AWG LiPo Pigtail
iFlight Support
More Information
| SKU | 11885 |
|---|---|
| UPC (GTIN) | 032733840059 |
| Manufacturer | iFlight |
| NDAA Compliant | No |
| Mounting Pattern | 20x20mm |
| Item Returns | This item can be returned |