Welcome to GetFPV My Account My Wishlist Log In

Holybro Kakute V2 - Atlatl HV - Tekko32 4-in-1 ESC Combo

Holybro Kakute V2 - Atlatl HV - Tekko32 4-in-1 ESC Combo
Holybro is saving you time and guesswork into making your perfect FPV stack. Comes with the Kakute V2 FC, Atlatl HV vtx, and the Tekko32 4-in-1 ESC.
Will Not Restock

Regular Price: $105.00

Special Price $99.99

Description

Holybro is saving you time and guesswork into making your perfect FPV stack. Comes with the Kakute V2 FC, Atlatl HV vtx, and the Tekko32 4-in-1 ESC. This is the stack found in the Holybro Kopis 1 Racing Drone.

Tekko32 35A 4-in-1 ESC

Features

  • 4-in-1 ESC with 30.5x30.5mm mounting holes, supports DSHOT 1200, BLHELI32 firmware
  • Added more CAPS to reduce power noise
  • 32bit ESC with BLHELI32 firmware
  • 4PWM input
  • Voltage output (VBAT), ESC Telemetry(TELEM)
  • Supports Oneshot / Multishot / Dshot PWM
  • Supports damped light
  • NO BEC

Specifications

  • Supports 3-6S lipo input
  • 35A continuous current, 50A burst
  • Mounting holes 30.5x30.5mm
  • Size: 55*40*6.4mm
  • Weight: 17g

Kakute F4 V2

New V2 Features

  • Two extra UART Ports
  • UART4 port for serial camera like the runcam split. (This is not the same as Betaflight Camera Control, which runs of the OSD menu for cameras like the swift, monster).
  • UART5 port for ESC telemetry support (for BLheli32 and KISS)
  • Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.
  • Barometer sensor on board allows altitude hold mode.
  • Dedicated I2C pads to connect extra peripherals (like an external compass)

Features

  • Supports Betaflight and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • Soft-mounting built in. The IMU ("gyro") chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
  • New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.
  • 2 oz. copper PCB allows up to 120A maximum continuous current.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on "BAT" pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.
  • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

  • MCU: STM32F405RGT6 32-bit processor
  • IMU: ICM20689 (SPI)
  • Barometer: BMP280
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 5 hardware UARTS (UART1,3,4, 5, 6)
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
  • 128 Mbit Dataflash chip for Blackbox logging
  • Dimensions: 35x30x8mm (includes USB in height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 7g

Atlatl HV

Features

  • Supports Betaflight and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
  • New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.
  • 2 oz. copper PCB allows up to 120A maximum continuous current.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “BAT” pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.
  • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

  • MCU: STM32F405RGT6 32-bit processor
  • IMU: ICM20689 (SPI)
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 3 hardware UARTS (UART1,3,6)
  • 128 Mbit Dataflash chip for Blackbox logging
  • Dimensions: 35x43x7mm (includes USB in height)
  • Mounting Holes: Standard 30.5mm square to center of holes 
  • Weight: 7g

Includes

  • 1x Tekko32 35A 4-in-1 ESC
  • 1x Kakute F4 V2 Flight Controller
  • 1x Atlatl HV Video Transmitter

Resources

Additional Information
SKU 8481
Manufacturer Holybro
UPC (GTIN) No
Reviews

FPV Regulatory Notice

The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your area. It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. GetFPV cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.

Also Purchased