The Happymodel ELRS X2 AIO Flight Controller comes with an integrated SPI 2.4GHz ExpressLRS receiver and 12A Blheli_S ESC which supports 2-4S. Bigger Mosfet supports high to 12A currents and would be better for a 2-4S toothpick drone or long-range FPV drone. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. Featuring an MPU 6000 SPI sensor and OSD, this board is the perfect addition to your FPV build.

Note: (Insert any product notes here in Red BOLD Italic. Example: "First Shipment expected January 2022" or "Electronics are Not Included".)

VIDEO: Diatone Mamba H743 MK4 FC & 128K ESC Unboxing

• 25.5 x 25.5mm Mounting Pattern
• F4 Flight Controller
• SPI ELRS Receiver
• 2-4S Lipo Input
• MPU 6000 SPI
• 12A ESC
• OSD

BINDING PROCEDURE

Connect ELRS X2 flight controller with computer by USB. Running Betaflight configurator and then move on Receiver tab then hit “Bind Receiver”. The Red LED on the flight controller starts blinking fast, which means the onboard SPI ELRS receiver is in bind mode.

Turn on your radio transmitter and run ELRS.LUA v2 version, scroll down the menu and hit [Bind]. The red LED on the flight controller would get solid first and then start to blink slowly. It means binding was successful. Re-connect the USB and then you will find the link was established.

• Amperage meter scale setting 470
• Voltage meter scale setting 110

F4 FLIGHT CONTROLLER

• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Receiver: Built-in SPI ExpressLRS 2.4GHz
• OSD: Built-in Betaflight OSD(SPI Control)
• Firmware Target: CRAZYBEEF4SX1280
• Sensor: MPU-6000(SPI connection)
• Mounting Pattern: 25.5×25.5 M2
• Power Supply: 2-4S Lipo battery
• ESC: Built-in 12A Blheli_s
• BEC: Built-in 5V 1A

ONBOARD SPI ELRS RECEIVER

• Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
• Antenna: Onboard SMD ceramic antenna
• Receiver Protocol: SPI ExpressLRS
• Telemetry output Power: <12dBm
• RF Frequency: 2.4GHz

ONBOARD 4-IN-1 ESC

• Default protocol: DSHOT150/DSHOT300/DSHOT600
• Currents: 12A continuous peak 15A (5 seconds)
• Power supply: 2-4S LiPo/LiPo HV (7v/17v)
• Factory firmware: F_H_40_REV16_8.HEX
• Support BLHeliSuite programmable
• MCU upgraded to EFM8BB21

IMPORTANT NOTES

• Insert important warnings or notes here. Example: "Do not overheat." or "Always use the included charger for best performance."

•  (Insert recommended products here. Example: "Battery: Lumenier 10000mAh 6s 25c Lipo Battery")

•   (Insert links such as manuals, firmware, etc)

• 1x Happymodel X2 AIO Board - F4 FC + SPI ELRS RX + 12A 2-4S ESC
• 1x Amass XT30U-M Connector
• 1x Hardware Set
• 2x 20AWG Wire
• 4x Grommets

ADD VIDEO TITLE HERE IN BOLD CAPS

ADD VIDEO TITLE HERE IN BOLD CAPS