Happymodel Mobula6 2024 1S 65mm Micro Whoop Analog V2.0 - UART ELRS 2.4GHz (Motor Plug)
$149.49
Out of Stock
Only left for same day shipping. Order now!
Happymodel Mobula6 2024 1S 65mm Micro Whoop Analog V2.0 - UART ELRS 2.4GHz (Motor Plug)
The Happymodel Mobula6 2024 V2.0 is a next-generation 65mm micro whoop built for ultra-light, high-performance indoor freestyle. Weighing just 17.7g, it features the upgraded SuperX ELRS V2.0 AIO flight controller with built-in Serial ELRS 2.4GHz and OpenVTX for crisp analog video.
About this product
The Happymodel Mobula6 2024 V2.0 is a next-generation 65mm micro whoop built for ultra-light, high-performance indoor freestyle. Weighing just 17.7g, it features the upgraded SuperX ELRS V2.0 AIO flight controller with built-in Serial ELRS 2.4GHz and OpenVTX for crisp analog video. Paired with ultra-light SE0702 motors and an FX17-B 800TVL camera, the Mobula6 delivers a smooth and powerful flying experience on a 1S battery.
Note: This micro whoop now features the SuperX ELRS V2.0 AIO 5-in-1 Flight Controller, equipped with a convenient motor plug, eliminating the need for soldering.
Features
- FX17-B 1/3 CMOS 800TVL Analog FPV Camera
- Integrated OpenVTX 5.8GHz Video Transmitter
- Designed for indoor freestyle and micro racing
- Lightweight SE0702 1.46g Brushless Motors
- Compatible with 1S LiPo / LiHV batteries
- SuperX ELRS V2.0 AIO Flight Controller
- Smooth and agile flight performance
- Built-in Serial ELRS 2.4GHz Receiver
- Plug-and-play motor connectors
Specifications
Motor (SE0702 KV28000)
- Configuration: 9N12P
- Stator Diameter: 7mm
- Stator Length: 2mm
- Shaft Diameter: 1mm
- Dimensions: Φ9.5mm × 14mm
- Weight: 1.46g
- Cell Compatibility: 1S only
Propeller
- Material: Polycarbonate (PC)
- Size: 31mm
- Pitch: 0.8 inch
- Weight: 0.21g
- Mount Hole Diameter: 1mm
Flight Controller (SuperX ELRS AIO 5-in-1)
- MCU: STM32F411CEU6 (100MHz, 512K Flash), ESP32-PICO-D4
- Gyro: BMI270 or ICM42688P (SPI)
- Mounting: 25.5mm × 25.5mm
- Power Supply: 1S (DC 2.9V–4.35V)
- Integrated Components:
- 5A (each) BLHeli_S 4-in-1 ESC
- Betaflight OSD (SPI control)
- 5.8GHz OpenVTX (0–400mW, MSP control)
- UART ExpressLRS v3.0.0 Receiver
- Voltage Meter (Scale: 110)
- Current Meter (Scale: 1175)
4-in-1 ESC (Onboard)
- Power Supply: 1S LiPo / LiHV
- Current: 5A continuous / 6A peak (3s)
- Firmware: Bluejay v0.19.2
- Protocol: DSHOT300
- Programmable via BLHeliSuite
- Recommended Startup Power: Min 1100 / Max 1200
Onboard Serial ExpressLRS Receiver
- Packet Rates: 50Hz / 150Hz / 250Hz / 500Hz
- Firmware: ExpressLRS v3.0
- Frequency: 2.4GHz
- Antenna: Enameled copper wire
- Telemetry Output Power: <12dBm
- Protocol: Serial-based CRSF
- Firmware Target:
- HappyModel AIO 2.4GHz RX+VTX
- Flashable via Wi-Fi
- Supported from ELRS v3.4.0 RC2
5.8GHz VTX (Onboard)
- Firmware: OPENVTX
- Control: MSP VTX
- PIT Mode Support: Yes
- Channels: 40
- Power Levels: 0 / RCE / 25mW / 100mW / 400mW
- Supply Voltage: DC 5V
- Current Draw (400mW): <650mA
- Antenna Connector: U.FL
Nano7 Camera
- Model: Nano7
- Sensor: 1/3″ CMOS
- Resolution: 800TVL
- FOV: D:150°, H:120°, V:98°
- Signal System: NTSC
- Weight: 1.9g (with cable)
- Dimensions: 14mm × 14mm × 13mm
Links:
Factory firmware and default dump file (Compatible with both v1.0 and v2.0 FC)
The AIO flight controller comes with two type of Gyro sensor , one is BMI270 and another one is ICM42688P
IMPORTANT NOTES
- So after you re-flashed firmware ,First Gyro direction for BMI270 should set to be CW0° , and for ICM42688P should set to be CW90°
Includes
- 1x Happymodel Mobula6 2024 V2 1S 65mm Micro Whoop Analog - UART ELRS 2.4GHz (Motor Plug version)
- 1x Hardware Set
More Information
| SKU | 22539 |
|---|---|
| UPC (GTIN) | 723326374807 |
| Manufacturer | Happymodel |
| Country of Manufacture | China |
| NDAA Compliant | No |
| Frame Style | Prop-Guarded |
| Prop Length | 65mm |
| Voltage | 1S |
| VTX System | Analog |