The Happymodel Crux3 NLR is a 18650 style Nano Long Range FPV quadcopter BNF. Very simple and convenient... plug in a single 18650 battery and then bind to fly. The Crux3 NLR comes with an AIO 5-in-1 ELRS F4 2.4GHz flight controller which means it has a built-in ExpressLRS high-performance radio link that provides a better range and stable connection.

Note: Battery not included. This version comes with a GPS.

VIDEO: #Crux3 NLR with ELRS F4 2G4 AIO FC and GPS 1S 18650 Nano Long Range FPV range test

Features

• Cruise time around 17 min with a single 18650 battery
• AIO 5-in-1 ELRS 2.4GHz flight controller
• Happymodel Mini M8N GPS and Buzzer
• High-performance radio link
• 1202.5 brushless motor
• CADDX ANT Camera
• 18650 Single battery

Specifications

• Camera: Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera
• VTX: Onboard 5.8G 25mw~200mw 40ch VTX (Flight controller built-in)
• Propellers: Gemfan 75mm bi-blade Propellers (4cw+4ccw
• Motors: Happymodel EX1202.5 KV11500 brushless
• Size: 125mmx115mmx40mm (without propellers)
• Receiver: Built-in SPI ExpressLRS 2.4GHz
• Frame: Happymodel Crux3 NLR
• GPS: Happymodel Mini M8N
• Weight: 68g (without battery)
• FC: ELRSF4 2G4 AIO 5-in-1
• Brand Name: Happymodel
• Item Name: Crux3 NLR
• Wheelbase: 135mm

Note: Because the AIO FC is compact and integrates high-power VTX, the core temperature of the flight controller will be very high. This is normal. We recommend tuning the drone under good cooling conditions.

CADDX ANT 1200tvl CAMERA

• Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
• Dimensions: 14*14mm (with a bracket to 19*19mm)
• Image Sensor: 1/3″ CMOS Sensor
• Min. Illumination: [email protected]
• Work Temperature: -20℃~+60℃
• Horizontal Resolution: 1200 TVL
• Wide Power Input: DC 3.7-18V
• S/N Ratio : >52dB (AGC OFF)
• TV System: NTSC or PAL
• Synchronization: Internal
• Auto Gain Control: YES
• IMAGE: 16:9 or 4:3
• Video Output: CVBS
• WDR: Global WDR
• Weight: 2g (N.W.)
• DNR: 3D DNR
• Lens: 1.8mm
• BLC: YES

ONBOARD 5.8GHz VTX

• Output power: 25mw~200mw switchable
• Frequency: 5.8GHz 5bands 40 channels
• Current consumption: 300mA(type)
• With Race bandSmartaudio ready
• Input voltage: 3.3V 5.5V
• Frequency: 40CH

ONBOARD SPI ELRS 2.4GHz RECEIVER

• Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
• Telemetry output Power: <12dBm
• RF Frequency: 2.4GHz
• Antenna: SMD antenna
• Note: Receiver protocol to flight controller: CRSF can bind with Happymodel ES24TX, ES24TX Lite, ES24TX Slim, and DIY 2.4GHz ELRS TX module

HAPPYMODEL MINI M8N GPS

• Features: GPS+SBAS or GPS+GLONASS+SBAS
• Warm start waiting time: 0.5~1.5minutes
• Sensitivity2 Tracking & Nav: –167 dBm
• Update rate: 5HZ Default, up to 10HZ
• Cold start waiting time: 3~5minutes
• Position Accuracy: 2.0 m CEP
• Chip Model: Mini M8N GPS
• Size: 20mm*20m*6mm
• Cold starts: –148 dBm
• Hot starts: –156 dBm
• Baudrate: 57600
• Weight: 6g

ONBOARD 4-IN-1 ESC

• Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
• Factory firmware: O_H_5_REV16_8.HEX
• Support BLHeliSuite programmable
• MCU upgraded to EFM8BB21
• Default protocol: DSHOT300

FLIGHT CONTROLLER

• Built-in 5A (each) Blheli_S 4in1 ESC Dshot600 ready
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Power supply: 1S battery input (DC 2.9V-4.35V)
• Built-in SPI ExpressLRS 2.4GHz receiver
• Firmware target: CRAZYBEEF4SX1280
• Sensor: MPU-6000(SPI connection)
• Built-in Betaflight OSD(SPI Control)
• Built-in 5V 1A BEC Flight controller
• Original whoop size compatible
• Built-in 5.8G VTX

MOTORS

• Motor Dimension:14x14.5mm
• Mode: EX1202.5 KV11500
• Shaft Diameter:Φ1.5mm
• Stator Diamter:12mm
• Stator Length:2.5mm
• Configuration:9N12P
• No.of Cells(Lipo):1S
• Weight(g):4.4g

PROPELLERS

• Center Hole diameter: 1.5mm
• Center Thickness:5mm
• Prop Diameter:75mm
• Gemfan 75mm
• Pitch:0.9in

Recommend (Not Included)

• Battery: Sony 18650 VTC6

Includes

• 1x Happymodel Crux3 NLR 1S 18650 FPV Drone w/ Caddx Ant Camera + ELRS + GPS
• 2x Gemfan 75mm bi-blade Propellers (4cw+4ccw)
• 1x 5D-OSD Menu Board
• 1x Hardware Kit
• 1x Screw Driver
• 1x Prop Tool