The SpeedyBee F7 V3 Flight Controller is an F722 FC featuring a BMP280 barometer, OSD, 500MB Memory Blackbox, a built-in FC LiPo monitoring system, and many more features. Equipped with solder-free connectivity options, this FC is the perfect addition to your FPV build.

Note: (Insert any product notes here in Red BOLD Italic. Example: "First Shipment expected January 2022" or "Electronics are Not Included".)

VIDEO: SpeedyBee F7 V3 Flight Stack - Everything But The Kitchen Sink

• 500MB Onboard Blackbox Flash memory
• 8 Motor output perfect for X8 Cinelifters
• 30.5 x 30.5mm Mounting Pattern
• FC LiPo Monitoring System
• Built-in Barometer
• 4 LED Plugs
• F722 FC
• Buzzer

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

• Power Output:
• 1) 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on the front side, and 6 +5V output included in the connectors on the bottom side. The total current load is 2A.
• 2) 2 groups of 9V output, one +9V pad on the front side and the other included in a connector on the bottom side. The total current load is 4A.
• 3) Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
• WiFi Support, used for data transfer, e.g firmware flashing, and Blackbox analysis.
• I2C: Supported. SDA & SCL pads on the front side. Used for magnetometer, sonar, etc.
• Support Flight Controller Firmware: BetaFlight
• ESC signal M1 - M4 on the bottom side and M5-M8 on the front side.
• LED: Used for WS2812 LED controlled by Betaflight firmware.
• UART: 5 sets (UART1, UART2, UART3, UART4, UART6)
• DJI Air Unit plug: A full DJI Air Unit JST slot onboard
• BLE Support, used for Flight Controller configuration
• Buzzer: BZ+ and BZ- pad used for 5V Buzzer
• Mounting: 30.5x30.5mm, 4mm hole size
• Dimensions: 41(L) x 38(W) x 8.1(H)mm
• OSD: BetaFlight OSD w/ AT7456E chip
• BlackBox: 500MB onboard data flash
• BetaFlight Camera Control Pad: Yes
• ESC Telemetry: UART UART4 RX
• Power input: 3S - 6S Lipo
• Target: SPEEDYBEEF7V3
• SmartPort: Supported
• Baro: BMP280 (I2C)
• MCU: STM32F722
• Boot button: Yes
• RSSI input: Yes
• IMU: BMI270
• USB: Type-C
• Weight: 9G

(INSERT VTX TITLE HERE IN BOLD CAPS)

IMPORTANT NOTES

• Insert important warnings or notes here. Example: "Do not overheat." or "Always use the included charger for best performance."

•  (Insert recommended products here. Example: "Battery: Lumenier 10000mAh 6s 25c Lipo Battery")

• SpeedyBee F7 V3 Stack Manual

• 1x SpeedyBee F7 V3 Flight Controller
• 1 4-Pin SH1.0 to SH1.0 Analog VTX Cable 60mm - Yellow and Blue
• 1x 6-Pin SH1.0 GPS module Cable without connector - 100mm
• 1 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable - 30mm
• 1 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable - 60mm
• 1 4-Pin SH1.0 to 4-Pin JST1.25 FPV Camera Cable - 60mm
• 1x 6-Pin SH1.0 GPS module Cable with connector
• 1 4-Pin SH1.0 Radio Receiver Cable - 100mm
• 1x SH 1.0mm 8-Pin Cable -30mm
• 5x M3 8mm Silicone Grommets
• 1x DJI 6-Pin Cable - 80mm

ADD VIDEO TITLE HERE IN BOLD CAPS

ADD VIDEO TITLE HERE IN BOLD CAPS