The SpeedyBee F405 Mini 20x20 Flight Controller is a testament to innovative drone technology, leveraging the advanced capabilities of the F405 chip, which outperforms its F411 counterpart. Integrated with a Bluetooth chip, it offers hassle-free wireless tuning via Betaflight, further enhancing the user experience.

Note: (Insert any product notes here in Red BOLD Italic. Example: "First Shipment expected January 2022" or "Electronics are Not Included".)

VIDEO: Diatone Mamba H743 MK4 FC & 128K ESC Unboxing

• Upgraded F405 Chip offers superior performance compared to the F411, ensuring smoother flight controls.
• Integrated Bluetooth allows for easy wireless Betaflight tuning.
• 4-level Battery Voltage Display gives pilots a clear insight into battery health and usage.
• In-built Barometer provides valuable altitude data for varied flight modes.
• DJI Air Units Compatibility ensures a perfect match with all DJI Air Units for improved video transmission.
• 4 UART Ports expand interfacing options with diverse peripherals.
• Dual BEC Setup with dedicated 5V 2A and 9V 3A outputs supports various device power needs.

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

USE BULLETED FEATURE HERE IN BOLD CAPS.

Add additional feature descriptions here to describe the above.

• MCU: STM32F405

• IMU(Gyro): ICM42688P

• USB Port Type: Type-C

• Barometer: Built-in

• OSD Chip: AT7456E chip

• BLE Bluetooth: Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please ensure the MSP switch on UART 4 is turned on and set to a baud rate of 115200. Otherwise, Bluetooth functionality will not be available.

• Wireless FC Firmware Flashing: NOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmware update

• Wireless Blackbox Download & Analysis: NOT Supported. Please connect to the Betaflight configurator on the PC to do a black box analysis.

• WIFI: Not supported

• DJI Air Unit Connection Way: Direct soldering

• DJI Air Unit Compatibility: Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD, and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input.

• Blackbox: 8MB Onboard Flash

• BetaFlight Camera Control Pad: Yes(CC pad on the front side)

• Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.

• Power Input: 3-6S LiPo. The flight controller is powered through the G, V wires of the 8-pin harness or G, V pads from the bottom side of the flight controller.

• 5V Output: 4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.

• 9V Output: 1 group of 9V output, one +9V pad on front side. The total current load is 3A.

• 3.3V Output: Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.

• 4.5V Output: Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

• ESC Signal: M1 - M4 wires or soldering pads on the bottom side.

• UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

• ESC Telemetry: UART R5(UART5)

• I2C: Supported. DA & CL pads on the front side. Used for magnetometer, sonar, etc

• Traditional Betaflight LED Pad: Supported. 5V, G, and LED pads on the bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware.

• Buzzer: BZ+ and BZ- pad used for 5V Buzzer

• BOOT Button: Supported. Press and hold the BOOT button and power the FC on simultaneously, forcing the FC to enter DFU mode; this is for firmware flashing when the FC gets bricked.

• RSSI Input: Not Supported

• Smart Port / F.Port: Not Supported

• Supported Flight Controller Firmware BetaFlight(Default), INAV

• Firmware Target Name: SPEEDYBEEF405MINI

• Mounting: 20 x 20mm 3.5mm hole diameter, Compatible with M2 and M3 screws/Silicone grommets.

• Dimension: 30(L) x 32(W) x 7.8(H)mm

• Weight 9.6g

IMPORTANT NOTES

• Insert important warnings or notes here. Example: "Do not overheat." or "Always use the included charger for best performance."

•  (Insert recommended products here. Example: "Battery: Lumenier 10000mAh 6s 25c Lipo Battery")

•   (Insert links such as manuals, firmware, etc)

• 1x Speedybee F405 Mini 3-6S 20x20 Flight Controller

ADD VIDEO TITLE HERE IN BOLD CAPS

ADD VIDEO TITLE HERE IN BOLD CAPS