Lumenier Mini 4Power + Plus Pro PDB (2-8S, 5v/9v Reg, 184A Curr.)

Lumenier Mini 4Power + Plus Pro PDB (2-8S, 5v/9v Reg, 184A Curr.)

Out of Stock

Only left for same day shipping. Order now!
Lumenier Mini 4Power + Plus Pro PDB (2-8S, 5v/9v Reg, 184A Curr.)
The Lumenier Mini 4Power + Plus Pro PDB (5v/9v Reg, 184A Curr.) (2-8s)

About this product

The Lumenier Mini 4Power + Plus Pro PDB is a feature-rich power distribution board designed for mini quadcopters. The board uses a native 20x20mm mounting hole pattern as well as a 30.5x30.5mm adapter board to fit different configurations. This PDB features an easy to solder layout keeping builds clean and simple. The Mini 4Power + Plus Pro has all your power needs in one place with a selectable onboard 5v or 9v 2A BEC as well as a 184A capable current sensor.

The 4Power + Plus Pro now supports a wider range of input voltage (2-8S LiPo) giving you more freedom in your builds than ever!

Updated with the times, the 4Power + Plus Pro has an 8-pin harness for plug n' play functionality with the Lumenier F7 Ultimate Flight Controller, (and other similar flight controllers) making setup that much easier. Another new feature on the + Plus Pro is the ability to get telemetry (BLHeli_32 features) and signal from your motors to pass through to the FC via the 8 pin connector.

The voltage regulator can supply up to 2A of current, allowing them to easily power your VTX, camera, FC, and some LEDs.


  • Input voltage range (2-8S operation)
  • PDB: 4x30A (Max.4x46A)
  • Regulated 5V (1.5A, 2A Max) and 10V (2A, 2A Max) outputs
  • Current Sensor ~184A (Output Voltage Scaling is 179)


  • 2oz copper, 4-layers &1.6mm PCB.
  • 1x Battery input, 4x ESC outputs. 2x BEC 5V outputs, 1x BEC 8V outputs.
  • Current Sensor, Gnd pads, Video Transmitter Signal & Gnd pads
  • Dimensions: 30x28(+8 with XT30)x4mm, Weight: 4.5g
  • Mounting holes 20mm square spacing, Φ3mm

PDB (ESC outputs)

  • Continuous current:  46A max per output

BEC 5V Outputs

  • Designed for RC Receivers, Flight controllers, OSD, and Servos.
  • DC/DC synchronous buck regulator.
  • Voltage: 5.0 +/- 0.1VDC
  • Continuous current: 1.5 Amps (Max.2A 10s/minute)
  • Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)
  • Short-circuit tolerant (5 seconds/minute)

BEC 9V Output

  • Linear regulator, very low noise. LC Filter is needless.
  • Designed for Video TX or FPV camera.
  • Stable power output even on low voltage 3s (below 12v)
  • Voltage: 8.0V +/- 0.3VDC (4~5S operation)
  • Continuous current: 1.5A@16V IN (2A Max)
  • Short-circuit tolerant (2 seconds/minute)

Current Sensor

  • ~184A


  • 1x Lumenier Mini 4Power + Plus Pro PDB
  • 1x 30.5x30.5 Mounting Adapter
  • 1x 8-pin to bare wire cable

More Information

SKU 10583
UPC (GTIN) 082652057847
Manufacturer Lumenier
Item Returns This item can be returned

Also Purchased

Lumenier QAV-R 2 Slam Freestyle Quadcopter Frame
As low as $74.99
Select Options
T-Motor F35A 3-5S 32bit ESC
Out of Stock
Out of Stock
Lumenier Razor F3 BLHeli_32 30A 2-6s ESC
Out of Stock
Out of Stock
Lumenier LUX F7 Ultimate Flight Controller (Dual Gyros)
Out of Stock
Out of Stock