Getting the right FPV camera settings can be a work in experimentation but it doesn’t need to be!\u00a0 Here, I will explain what each setting does, and how it impacts your overall picture quality and share my FPV camera settings as a place for you to get started.\u00a0\u00a0Often, people don’t truly understand what all the different settings mean, much less what they do.\u00a0 However, armed with the proper knowledge, we can all be a little more well rounded.[vc_row][vc_column][vc_single_image image=”822″ img_size=”full” alignment=”center”][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n
The cameras that we currently use for FPV, began life long ago as security cameras.\u00a0 Through exploring the options within the OSD, you will begin to see this history come to light within the firmware that drives these little guys.\u00a0 They also have been used in the automotive industry for rear view cameras, and you\u2019ll see some of those settings.\u00a0 Many out there are looking for the \u201cperfect\u201d settings, but let me begin by telling you this: There are no perfect FPV camera settings, only settings that are perfect for the situation that you are currently flying in!<\/em><\/strong>\u00a0 <\/em>However, there are settings that work well in a broad spectrum of circumstances and toward the end, I will share what has worked well for me over the past few years.<\/p>\n Now, as you may have found during your research and shopping, there are many different cameras, from many different companies.\u00a0 While most cameras operate with similar technology, small differences in image sensors, image processors, and other components will change the way your camera will perform, and how the image will look.\u00a0 It also may change some of the locations of the menu options.\u00a0 Also keep in mind that on a much higher level, my eyes might perceive things differently than yours do, and the way one person sets up their camera may not look good to you.<\/p>\n Before we get into the FPV camera settings, let\u2019s focus your camera lens.\u00a0 I use a focusing chart that I can tape up onto the wall about 15 feet away from the camera.\u00a0 Loosen the retaining ring on your lens, and you can either screw the lens in or back it out a little while pointing it at the focus chart.\u00a0 You want all the lines to be as crisp as possible.\u00a0 When done, tighten down the retaining ring snuggly.\u00a0 You can get a focusing chart here: http:\/\/www.ifpv.co.uk\/focus_pattern.pdf<\/a>[\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column width=”1\/6″][\/vc_column][vc_column width=”2\/3″][vc_single_image image=”829″ img_size=”full” alignment=”center” onclick=”link_image”][\/vc_column][vc_column width=”1\/6″][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n So with that said, let\u2019s get into the FPV camera settings.\u00a0 Down below I will go into detail of what each function does, that way you go into this process with a little understanding of what everything is, and how it could affect your picture.\u00a0 But first, let’s get the remote hooked up to the back of the camera.\u00a0 Most FPV cameras come with these, and styles may differ between brands, but I generally use the cable pictured above, and hook up the RCA connector to my television.\u00a0 I power the camera with my Fatshark goggle battery.\u00a0 It is also possible to edit these settings once the camera is installed on your build by simply hooking up the remote.<\/p>\n The remote above seemingly has one button, but it functions as a multi-position switch.\u00a0 You can move it up, down, left and right, as well as push down on it when centered as the “enter” button.\u00a0 From here, push down on the button, and you will enter your camera menu.\u00a0 There are also other versions that are on a PCB, and have 5 individual buttons.\u00a0 Either works, as long as it’s compatible with your camera.\u00a0 If you are like me, I have several of each style taking up space in my work area.[\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column width=”1\/6″][\/vc_column][vc_column width=”2\/3″][vc_single_image image=”834″ img_size=”full” alignment=”center” onclick=”link_image”][\/vc_column][vc_column width=”1\/6″][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n The lens setting exists mostly for applications outside of our own use.\u00a0 Here in this menu, you get three settings: Manual, DC, and Video.\u00a0 This setting exists for cameras that have an \u201cAuto Iris\u201d lens on them.\u00a0 The different settings are for cameras that have the ability to drive those lenses.\u00a0 An iris is a mechanical element that can be opened or closed to let in more or less light respectively.\u00a0 Manual is the option that you want to choose here, as our lenses are \u201cFixed Iris\u201d, meaning that the lens will always allow in as much light as possible.[\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column width=”1\/6″][\/vc_column][vc_column width=”2\/3″][vc_single_image image=”923″ img_size=”full” alignment=”center”][\/vc_column][vc_column width=”1\/6″][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n The exposure option is going to be what we call a breakout menu, in which it will give you access to several options.\u00a0 Under here are a few items that we are going to modify settings.<\/p>\n This option allows you to set the shutter speed to specific light levels. Due to the nature of our flying, setting this to a fixed number can lead to you image blowing out from too much light, or getting too dark as you fly through a shaded area.\u00a0 The only time that I would recommend changing this is if you were flying at night, in a very dark area.\u00a0 You would set the shutter speed to the lower settings to lock it in to ensure it doesn\u2019t change unexpectedly on you.<\/p>\n Brightness is going to do exactly what you think it will, affect the overall brightness of the image.\u00a0 The higher you go, the brighter the image will be.\u00a0 No mystery here!<\/p>\n AGC is useful for adapting your camera image to lower light conditions.\u00a0 It gives you four settings: Low, Medium, High, and Off.\u00a0 You won\u2019t notice this kick in until your camera is looking at a low light setting, so I recommend adjusting this while point the camera toward a dark area.\u00a0 Simply alternating between looking at a lamp, for example, then looking at a dark corner of the room, will give you an example of what this looks like.\u00a0 It takes about a second for it to kick in as well and it will introduce noise artifacts into your image.<\/p>\n DWDR stands for Digital Wide Dynamic Range.\u00a0 \u00a0When on, it will sample the light areas and dark areas, and automatically compensate the image to balance the two out so that all areas in the image are visible in detail.[\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column width=”1\/6″][\/vc_column][vc_column width=”2\/3″][vc_single_image image=”834″ img_size=”full” alignment=”center”][\/vc_column][vc_column width=”1\/6″][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n If you\u2019re familiar with photography, different sources of light emit different colors, which can lead to images favoring one color over another.\u00a0 As an example, standard daylight tends to be more in the blue spectrum, while indoor lighting is more in the red spectrum.\u00a0 There are a few options here that you can manipulate, two settings for auto white balance (ATW 1 and ATW 2), a manual setting in which you can modify sliders for red and blue, and a WB Set function.<\/p>\n To use the WB Set function, set a white object (a plain piece of printer paper works nicely) on the ground where it is illuminated by whatever light source you plan on flying in, for example the sun.\u00a0 Make sure there are no shadows present on the paper, then point your camera at the paper so it is the only thing in the image.\u00a0 Then with the cursor on your camera set to WB Set, press the center button.\u00a0 The camera will then set itself as that image for white, and all images will be color correctly for that environment.\u00a0 Often times, I set mine to a bright sunny (and often HOT!!) day here in Arizona, and leave it set that way permanently unless flying in an indoor or extremely different environment.\u00a0 Most days here are sunny so for me it works well.<\/p>\n This option is mainly a throwback to the security camera, and an option that generally is replaced by the DWDR option above.\u00a0 There are three options, OFF, BLC (Backlight Compensations), and HLC (Highlight Compensation).\u00a0 While not a setting we generally use, Backlight Compensation is for instances when the subject in the foreground has a strong light source behind it, and adjusts the image to brighten the foreground.\u00a0 Highlight compensation is the exact opposite, when there is a strong light source in the foreground, but the background is dark, the image is adjusted to lower the bright object so more image is visible.<\/p>\n Day and Night is an option that allows the camera to switch between color or black and white depending on the amount of light available.\u00a0 These cameras often have better imaging in low light situations when set to black and white. Depending on your personal preferences, you may not like the black and white mode.<\/p>\n There are several options here: Color will keep it in color mode at all times, B&W will keep it in black and white at all times, and Auto, in which it will switch between the two depending on light levels.\u00a0 Auto also has settings within it that allow you to set the level at which it will automatically switch, and the time delay before it switches.<\/p>\n This option prompts you to put your lens cap on or cover the lens so no light gets to the image sensor, and then runs a check, looking for dead or hot pixels.\u00a0 Once detected, the image processor then identifies that pixel for \u201cauto-completion\u201d.\u00a0 This will fill that pixel in with an average of the pixels around it.\u00a0 Most guides will tell you to ignore this, but I do run it from time to time so that I don\u2019t have that one bright pixel that causes a distraction in my video.\u00a0 I also run this when the camera is right out of the box, before it goes into my build.[\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column width=”1\/6″][\/vc_column][vc_column width=”2\/3″][vc_single_image image=”924″ img_size=”full” alignment=”center”][\/vc_column][vc_column width=”1\/6″][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n Again, like the exposure menu, there are multiple options nested under here, and there are a few options that we will want to adjust.<\/p>\n This is where you can set your pilot name, frame name, or whatever other identifier you want to display on your image feed.\u00a0 Character space is limited to nine characters.\u00a0 If shorter, in order to center it properly you will need to add spaces at the beginning.\u00a0 Also, once your identifier is set, on the top menu, you will want to make sure to turn this option on.<\/p>\n Option for security cameras that calls out areas with motion.\u00a0 Not something we need.<\/p>\n Option for security cameras to block off certain areas of the image.\u00a0 Not useful\u2026. We want the whole picture!<\/p>\n Option for rear view cameras on vehicles, adds distance markers for reversing.\u00a0 While not something we generally use, I have seen some pilots use this to assist with lining up gates.[\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column width=”1\/6″][\/vc_column][vc_column width=”2\/3″][vc_single_image image=”836″ img_size=”full” alignment=”center”][\/vc_column][vc_column width=”1\/6″][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n Here we have another nested menu in which we will be making several adjustments.<\/p>\n Here you have the option to turn it on or off, and when on, you can go in a set the level.\u00a0 Changing the level up will slightly increase visibility in lower light areas, however it introduces noise artifacts into the image.\u00a0 Adjust carefully if you choose to use this.<\/p>\n 2DNR is a Digital Noise Reduction setting that reduces noise artifacts in the image by blurring the surrounding pixels.\u00a0 This can work against the pilot by potentially hiding smaller objects that could be an obstruction to your model.\u00a0 When set to on, you can access a menu to adjust the level.<\/p>\n Mirrors your image across the vertical axis, effectively making right and left reversed.\u00a0 This is not something we want to use, could be a little confusing!<\/p>\n Option that will allow you to change the color of the font in the menu and your camera title identifier.<\/p>\n Slider that will adjust the ratio of difference between blacks and white levels of your image.\u00a0 Finding a proper balance between these is critical, as too much will cause your video to blow out in bright areas.<\/p>\n Slider that will adjust how sharp edges in the image are.\u00a0 The lower setting will make object blur slightly, making the image appear to be slightly out of focus, and the higher settings create more defined edges in the video.\u00a0 Set to high, it can introduce a little bit of noise.<\/p>\n This setting optimizes the video for display on different display types.\u00a0 Here you have three different options, LCD, CRT, and USER.\u00a0 Within each of these settings, you can adjust several more options, the GAMMA, COLOR GAIN, and PED LEVEL.\u00a0 As most monitors, displays, and googles use LCD technology (when\u2019s the last time you saw a CRT TV or Monitor), I recommend setting this to LCD.<\/p>\n GAMMA will adjust the brightness of the overall picture, but setting it too high can lead the picture to feel washed out.\u00a0 COLOR GAIN will change the amount of color saturation in the picture.\u00a0 Setting it low will strip the image of all color leaving you with a greyscale image, and setting it high will over saturate the color in your video.\u00a0 PED LEVEL will adjust the levels of what dark areas are considered black in your image.\u00a0 The lower the settings, the more dark areas become black, and the higher the level, the more distinguished the different dark areas will be, however the image may appear lighter than real life.<\/p>\n This setting will completely reverse the colors of the image, making it look like a negative from film.[\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column width=”1\/6″][\/vc_column][vc_column width=”2\/3″][vc_single_image image=”834″ img_size=”full” alignment=”center”][\/vc_column][vc_column width=”1\/6″][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n This brings us to the end of the FPV camera settings.\u00a0 Through this option, you can reset your camera to the factory settings.\u00a0 This is useful if you have been playing around with all the settings, and have a picture beyond what you want to try and correct.<\/p>\n Before you unplug your camera, you want to use the EXIT command at the top menu, otherwise your settings will not be saved.\u00a0 Once done, make sure and double check the focus, as it may need a slight adjustment.[\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column width=”1\/6″][\/vc_column][vc_column width=”2\/3″][vc_single_image image=”838″ img_size=”full” alignment=”center”][\/vc_column][vc_column width=”1\/6″][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n Below you will find my FPV camera settings.\u00a0 Now keep in mind these work well for me, but they may not be exactly<\/em> what you are looking for or prefer.\u00a0 However, these should get you in the range of being able to see what you need to see, and you can make minor adjustments yourself.\u00a0 Also, remember, settings may slightly differ from brand and type of camera as well.\u00a0 Please, feel free to experiment!\u00a0 There is never a single way to do something in this hobby\u2026. That\u2019s what makes it great!\u00a0 Happy flying![\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n .[\/vc_column_text][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n Don’t be afraid to take my guide and modify for yourself!\u00a0 Getting your FPV camera settings exactly how you want will only heighten your experience and immersion.\u00a0 It will also allow you to see the world around you.\u00a0 Remember, your FPV camera is your portal to the world while flying and none of us would be in this hobby if that view wasn’t a part of the thrill.<\/p>\n Feel free to share your FPV camera settings in the comments below for others to use.\u00a0 The only way we learn is to share what works best for us![\/vc_column_text][\/vc_column][\/vc_row]<\/p>\n","protected":false},"excerpt":{"rendered":" An In Depth Look at FPV Camera Settings Getting the right FPV camera settings can be a work in experimentation but it doesn’t need to be!\u00a0 Here, I will explain what each setting does, and how it impacts your overall picture quality and share my FPV camera settings as a place for you to get … Read more<\/a><\/p>\n","protected":false},"author":2,"featured_media":869,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[133],"tags":[421,418,683,420,678,680,679,685,681,684,422,682],"class_list":["post-816","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-fpv-essentials","tag-drone","tag-drone-racing","tag-foxeer","tag-fpv","tag-fpv-camera","tag-fpv-camera-settings","tag-fpv-settings","tag-getfpv","tag-hs1177","tag-lumenier","tag-quadcopter","tag-runcam","infinite-scroll-item","generate-columns","tablet-grid-50","mobile-grid-100","grid-parent","grid-33"],"_links":{"self":[{"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/posts\/816","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/comments?post=816"}],"version-history":[{"count":58,"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/posts\/816\/revisions"}],"predecessor-version":[{"id":1283,"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/posts\/816\/revisions\/1283"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/media\/869"}],"wp:attachment":[{"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/media?parent=816"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/categories?post=816"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.getfpv.com\/learn\/wp-json\/wp\/v2\/tags?post=816"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}Different Cameras, Different Settings<\/h2>\n
Focusing your Camera<\/h2>\n
Camera Settings<\/h2>\n
Lens<\/h3>\n
Exposure<\/h3>\n
Shutter<\/h4>\n
Brightness<\/h4>\n
AGC (Automatic Gain Control)<\/h4>\n
DWDR (Digital Wide Dynamic Range)<\/h4>\n
White Balance<\/h3>\n
Backlight<\/h3>\n
Day and Night<\/h3>\n
DPC (Dead Pixel Correction)<\/h3>\n
Special<\/h3>\n
Cam Title<\/h4>\n
Motion<\/h4>\n
Privacy<\/h4>\n
Park Line<\/h4>\n
Image Adjust<\/h4>\n
Lens Shad<\/h5>\n
2DNR<\/h5>\n
Mirror<\/h5>\n
Font Color<\/h5>\n
Contrast<\/h5>\n
Sharpness<\/h5>\n
Display<\/h5>\n
Neg. Image<\/h5>\n
Reset<\/h3>\n
Exiting the Settings<\/h2>\n
FPV Camera Settings<\/h2>\n
Optimal FPV Camera Settings<\/h3>\n
\n
\n
\n
\n
\n
\n
Experiment!!<\/h2>\n