ImmersionRC Tramp/Ghost Hybrid UNO V2 2.4GHz Rx & 25-600mW 5.8GHz VTX
ImmersionRC Tramp/Ghost Hybrid UNO V2 2.4GHz Rx & 25-600mW 5.8GHz VTX
Out of Stock
About this product
The new ImmersionRC Tramp/Ghost Hybrid UNO V2 is a high-end analog 5.8GHz 25mW - 600mW video transmitter and 2.4GHz diversity receiver!
There is nothing like the experience of flying an FPV drone, but building these marvelous machines is more complex than it needs to be. With Tramp, ImmersionRC has set out to raise the bars on video transmitter technology. With Ghost, ImmersionRC has set out to redefine the norms in receivers for R/C control. And now ImmersionRC has fused these two together in the groundbreaking Ghost Hybrid. Designed by pilots, built by pilots, supported by pilots.
Features
- 20 x 20mm Mounting
- Single-sided PCB with gummies included
- Only 2.2g, perfect for the sub-250g class
- Long-range AND low latency
- 250Hz updates
- 2.4GHz LoRa and FLRC Control
- 5.8GHz 1-600mW Video Transmitter
- All 48 Standard Channels
- Thermally regulated, Factory calibrated
- 500Hz/1kHz ready for when OpenTx can supply quality data at this rate
- Available vTx channels and power may vary from region to region to comply with local regulations
- 2.4GHz ISM Band
- Tiny 15 x 12mm, and 0.61g
- Crazy Race Performance, 222.22Hz updates (500Hz Ready)
- 4ms End to End Latency (2ms ready), with OpenTx Integration
- Fully supported by Betaflight with GHST driver
Specifications
- Downlink RF Power: +13dBm
- Sensitivity: -117dBm in Long Range mode
- Serial Formats: GHST, SBus, SBus-Fast (200k), SRXL-2 (400k), SBus Inverted
- Firmware: Over-the-air (OTA) upgradeable (Rx and VTx)
- Power Supply: 5V, with Over Voltage Protection
- VTX Control: Automatic, via Ghost
- Antenna Connectors: Standard U.FL with Locking Connectors
- Dimensions: 26mm x 126mm, 2.2g (w/o antennas)
Intelligent VTX Control
Intelligent, and direct control of the video transmitter from the Ghost ecosystem. Use either the OLED menus on the Ghost Transmitter module or the responsive OpenTx tools menu. Tx remains silent on power-up, shuts down immediately in an (unlikely) failsafe.
Locking Connectors
Innovative locking connectors deliver the advantages of the lightweight u.FL/MHF standard, with the security required for world-class racing, or long-range flying. Simply plug the connector onto the board, and slide the locking cap to secure.
Thermal Regulation + Calibration
As with all tramp products, the Hybrid includes automatic thermal regulations, protecting the video transmitter against potentially damaging overheating while sitting on the starting pad. The onboard Tramp is factory calibrated, for precise power delivery during critical race events.
qTee Antennas
qTee, a.k.a ‘Cutie’ antennas are center-fed dipoles, with integral balun to ensure no cable radiation, and without unexpected nulls in the radiation pattern. Tip to Tip length of just 60mm, easy to install in anything from a Whoop™ to an X-Class quad
Manual
Firmware/ Downloads
- OpenTx 2.3.11 Synced Build (6.4 MB)
- Ghost Updater macOS Edition v1.5 (12.5 MB)
- Ghost Updater Edition Version v1.4 (51.4 MB)
- Ghost OpenTx Widgets (6.9 KB)
- ImmersionRC Drivers (Windows) (525.2 KB)
- Notes on firmware found HERE
Includes
- 1 x ImmersionRC Tramp/Ghost Hybrid UNO V2 2.4GHz Rx & 25-600mW 5.8GHz VTX
- 1 x Silicone Cable
- 2 x qTee Antenna
More Information
| SKU | 17033 |
|---|---|
| UPC (GTIN) | 764613336337 |
| Manufacturer | ImmersionRC |
| NDAA Compliant | No |
| Item Returns | This item can be returned |