Immersion RC Ghost Hybrid 5.8GHz vTx/2.4GHz Rx
Immersion RC Ghost Hybrid 5.8GHz vTx/2.4GHz Rx
About this product
There is nothing like the experience of flying an FPV drone, but building these marvelous machines is more complex than it needs to be. With Tramp, we set out to raise the bar on video transmitter technology. With Ghost, we set out to redefine the norms in receivers for R/C control. And now we have fused these two together, in the groundbreaking Ghost Hybrid. Designed by pilots, built by pilots, supported by pilots.
Features
- Available vTx channels and power may vary from region to region to comply with local regulations
- 500Hz/1kHz ready for when OpenTx can supply quality data at this rate
- 4ms End to End Latency (2ms ready), with OpenTx Integration
- Crazy Race Performance, 222.22Hz updates (500Hz Ready)
- Fully supported by Betaflight with GHST driver
- Single-sided PCB with gummies included
- Only 2.2g, perfect for the sub-250g class
- Thermally regulated, Factory calibrated
- Two fully independent Ghost receivers
- 5.8GHz 1-600mW Video Transmitter
- 2.4GHz LoRa and FLRC Control
- Long-range AND low latency
- Tiny 15 x 12mm, and 0.61g
- All 48 Standard Channels
- 20 x 20mm Mounting
- 2.4GHz ISM Band
- 250Hz updates
INTELLIGENT VTX CONTROL
Intelligent, and direct control of the video transmitter from the Ghost ecosystem. Use either the OLED menus on the Ghost Transmitter module or the responsive OpenTx tools menu. Tx remains silent on power-up, shuts down immediately in an (unlikely) failsafe.
LOCKING CONNECTORS
Innovative locking connectors deliver the advantages of the lightweight u.FL/MHF standard, with the security required for world-class racing, or long-range flying. Simply plug the connector onto the board, and slide the locking cap to secure.
THERMAL REGULATION + CALIBRATION
As with all tramp products, the Hybrid includes automatic thermal regulations, protecting the video transmitter against potentially damaging overheating while sitting on the starting pad. The onboard Tramp is factory calibrated, for precise power delivery during critical race events.
qTee ANTENNAS
qTee, a.k.a ‘Cutie’ antennas are center-fed dipoles, with integral balun to ensure no cable radiation, and without unexpected nulls in the radiation pattern. Tip to Tip length of just 60mm, easy to install in anything from a Whoop™ to an X-Class quad
Specifications
- Serial Formats: GHST, SBus, SBus-Fast (200k), SRXL-2 (400k), SBus Inverted
- Antenna Connectors: Standard U.FL with Locking Connectors
- Firmware: Over-the-air (OTA) upgradeable (Rx and VTx)
- Dimensions: 26mm x 126mm, 2.2g (w/o antennas)
- Power Supply: 5V, with Over Voltage Protection
- Sensitivity: -117dBm in Long Range mode
- VTX Control: Automatic, via Ghost
- Downlink RF Power: +13dBm
Manual
Firmware/ Downloads
- OpenTx 2.3.11 Synced Build (6.4 MB)
- Ghost Updater macOS Edition v1.5 (12.5 MB)
- Ghost Updater Edition Version v1.4 (51.4 MB)
- Ghost OpenTx Widgets (6.9 KB)
- ImmersionRC Drivers (Windows) (525.2 KB)
- Notes on firmware found HERE
Includes
- 1x Immersion RC Ghost Hybrid 5.8GHz vTx/2.4GHz Rx
- 4x Damping Balls (Red)
- 1x Silicone Cable
- 2x qTee Antenna
More Information
SKU | 15823 |
---|---|
UPC (GTIN) | 736952010032 |
Manufacturer | ImmersionRC |
NDAA Compliant | No |
Item Returns | This item can be returned |