This is a next gen. flight controller featuring the STM32F405 processor and MPU6000 gyro. The advanced F4 processor gives this FC incredible precision and control while in the air. This flight controller includes 3 UART connections with SBUS, PPM or Serial RX and has a 3.3v output for Spektrum receivers as well as a hardware boot button. The board has been designed around the popular CC3D Revolution target and is fully support by RaceFlight, BetaFlight and CleanFlight. It comes preloaded with BetaFlight firmware.
- Weight: 5g
- 36mm x 36mm (standard 30.5mm between mounting holes)
- Support raceflight and betaflight firmware, default is BF.
- Use MPU6000 accelerometers and gyroscopes
- Gyro and MCU have 3.3V independent power supply
- Support LED strip and blackbox
- Has outputs for up to 6 motors (ESCs)
- Three available hardware UART ports
- Built in inverter for SBUS input
- STM32F405 32-bit processor at 168MHz, 1Mb flash, 192kb ram
- Micro USB connectivity using STM Virtual Communications Port
- M25P16 16 Mbit, serial Flash memory, 75 MHz SPI bus interface
- 1x7pin JST-SH socket (SUBS,SERIAL,RX,TX,5V,GND)
- 6X3pin though-holes for pin headers for ESC
- No BEC
- Input voltage: 5 ~ 8.4V
- Firmware target: REVO / CC3D Revolution
- 1x F4 Advanced Flight Controller - (MPU6000, STM32F405)
- 1x 1x7 pin header straight
- 1x 3x6 pin header straight
- 1x 3x6 pin header right angle
Based on the CC3D Revolution and designed by Bob Forooghi (FPV Kabab) in collaboration with Sunrise Model.
Cheap fc ..quality component review by Ashley on 7/5/2017
I love mine...in a 217mm with dys fires 4s battery it is awesome . .....going to buy more for future builds.....
Impressed... review by Sentinel Aerial Video on 6/24/2017
I know that finding info on this FC on the internet is hard so here's what I discovered. Choose CC3D (Revo) for board and update to newest version if desired. Remember, you have a virtual port so do NOT mess with that setting. Use RX3 on FC board for satellite (Gray wire), which is UART3 in port settings and enable serial RX. Red goes to 3.3V and black goes to ground. In config. make sure you select Spektrum2048 or you RC will go crazy. Fine tune min and max (1000 -2000) on remote under receiver. Anyway, nice and simple but powerful little FC.
Great flight controller at any price review by Parts for power on 6/19/2017
Purchased 2 of these and they fly like they are on rails. Buzzer is a pain in the butt you must connect buzzer ground to signal #6 and put this command in CLI
resource MOTOR 6 NONE
resource BEEPER A00
Great for the price but... review by harris on 3/22/2017
This is a quality FC. My only grudge are the little things, but they've pushed me to using other boards - no power to rx under usb, only under lipo power, and I prefer edge mount to the 3 layer through hole. The lack of 5v to the rx under usb power is exceptionally annoying but for the price this is an awesome piece of kit.
It works review by Michael Jason on 1/29/2017
So far this fc works great. I like the idea that Beta flight is already flashed onto it.
Updating to 5 stars review by Jacob on 1/2/2017
I'm updating my review to 5* because this FC works great. Problem is they say to use UART1 with spektrum sat, however this will not work since UART 1 shares the USB port. Switched to UART 3 and this board is on rails. Highly recommend! Especially for the price!!
Great FC for the Mula! review by Steven on 12/10/2016
Great Flight controller! 32k speeds like a Lux. You're not going to better than this with current components. If you want a Buzzer then in the BF CLI paste the following:
resource MOTOR 6 NONE
resource BEEPER A00
Seemed good to start review by Jacob on 12/9/2016
Have about 7 flights on the board, and like the reviewer above mentioned, I too couldn't get a spektrum sat to work on UART 1 and had to use UART3. Not that big of a deal, board seemed to fly on rails. Until yesterday after 7 flights go to change packs and my sat would no longer light up or work. Got home checked the pads and it's putting out 3.2v now not 3.3v. Tried a brand new sat and same thing no lights no nothing. At this point it seems like a regulator issue. Going to contact GetFpv about the issue, maybe they will send a replacement board or something. The price is right and the mpu6000 is where it's at. Just need it to last me.
Overall I'd try another. If it truly is a faulty board I'll update my review.
Great review by John on 11/29/2016
Great Fc. About to buy my next one. At a great price point
Would not flash review by Aaron on 11/28/2016
I could not get the board to flash with beta flight or clean flight. no matter what computer i used ( windows 10, 8.1, 7) i just would not flash.
replacing all cc3d with this review by James on 11/19/2016
Had this up and running in 20 minutes. That's soldering pin headers too. Super simple! Taranis is UART 1 and mapping is TAER1234. which is odd. But, works as it should with sbus. Ordering more while they're in stock.
Simple & great handling review by Lamar on 11/15/2016
Works great with Lumenier 35 amp esc Belheli S & high KV smooth & locked in. X frame of course. Price is great if you're just racing
Great budget barebone F4 review by craig on 11/9/2016
Great F4 with mpu6000 gyro. Perfect replacement for any F3 with mpu6000. Finally we aren't limited by the processing power like an F3 @ 8k. Probably the most simple layout ever. Reminds me of Naze rev5. It has a 5v rail, 3.3v output for spektrum sat rx, sbus and much more. Been flying this FC for almost 2 weeks now and it has been great. I am running 8k/8k/8k BF 3.0.1 soft mounted with ninjaflex standoffs. Wish it did have vbat but that would just create more noise to the gyro. Separating everything from the FC is back again and I am completely fine with that if its butter smooth flights. CPU usage 3% with acc, bar, mag off, feature: airmode. (8k) If you want a osd and vbat with this board check out the RROSD EVO pdb+osd or matek tp pair up. ($41.98 osd, vbat, current sensor with pdb,+ F4 FC) Not bad!
Hardware spec looks good review by Robert on 11/8/2016
I posted a bad review of this on getfpv.com I thought they didn't post the review, and it made me really bitter with them as a company. I WAS WRONG!! They changed the product I think based on my review. The previous version used an Bosh160 gyro, which was going to be terrible and limited to 1.6K or some BS like that meaning the best you could run would be 1K looptime, which at that point an F4 board is pointless just keep flying that 2 year old Naze32. They redesigned the product and released it with a MPU6000 gyro which will support 8K looptime and apparently even higher, I haven't tried it on any MPU6000 yet. Although I haven't tried one personally, based on the hardware spec I can't say anything bad about it at this time, and way to go to getfpv. Looks like a really good budget F4 board. Only dig I can say is that they should take a page from the new race flight boards and put the gyro in the center of the board. But we all know off-center gyros fly well, it's what we have been flying unknowingly for the last 4 years.
Very Basic F4, but flies nice review by Christopher on 11/6/2016
Flies nice (32K motor loop, 8K Gyro, 8K PID loop)
Really Low Price F4
Couldn't get Spektrum to work on UART1, had to use UART3.
(Maybe something I did.. doubt I though)
LED is motor pin 5...
No Vbat (mimimom OSD users, not the board for you)
No Mounting hardware included (better order some with it)
I like the FC, it's been flying great for me, but do I have to solder jumpers if I want to use Race Flight on it? There is no documentation other than the pictures on the site.