Welcome to GetFPV My Account My Wishlist Log In

Holybro Kakute V2 - Atlatl HV V2 - Tekko32 35A 4-in-1 ESC Combo

Holybro Kakute V2 - Atlatl HV V2 - Tekko32 35A 4-in-1 ESC Combo
Holybro is saving you time and guesswork into making your perfect FPV stack. Comes with the Kakute V2 FC, Atlatl HV V2 VTX, and the Tekko32 35A 4-in-1 ESC.
In Stock
$105.00
OR
Description

Holybro is saving you time and guesswork into making your perfect FPV stack. Comes with the Kakute V2 FC, Atlatl HV vtx, and the Tekko32 4-in-1 ESC. 

Tekko32 35A 4-in-1 ESC

Features

  • 4-in-1 ESC with 30.5x30.5mm mounting holes, supports DSHOT 1200, BLHELI32 firmware
  • Added more CAPS to reduce power noise
  • 32bit ESC with BLHELI32 firmware
  • 4PWM input
  • Voltage output (VBAT), ESC Telemetry(TELEM)
  • Supports Oneshot / Multishot / Dshot PWM
  • Supports damped light
  • NO BEC

Specifications

  • Supports 3-6S lipo input
  • 35A continuous current, 50A burst
  • Mounting holes 30.5x30.5mm
  • Size: 55*40*6.4mm
  • Weight: 17g

Kakute F4 V2

New V2 Features

  • Two extra UART Ports
  • UART4 port for serial camera like the runcam split. (This is not the same as Betaflight Camera Control, which runs of the OSD menu for cameras like the swift, monster).
  • UART5 port for ESC telemetry support (for BLheli32 and KISS)
  • Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.
  • Barometer sensor on board allows altitude hold mode.
  • Dedicated I2C pads to connect extra peripherals (like an external compass)

Features

  • Supports Betaflight and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • Soft-mounting built in. The IMU ("gyro") chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
  • New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.
  • 2 oz. copper PCB allows up to 120A maximum continuous current.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on "BAT" pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.
  • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

  • MCU: STM32F405RGT6 32-bit processor
  • IMU: ICM20689 (SPI)
  • Barometer: BMP280
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 5 hardware UARTS (UART1,3,4, 5, 6)
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
  • 128 Mbit Dataflash chip for Blackbox logging
  • Dimensions: 35x30x8mm (includes USB in height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 7g

Atlatl HV V2

Features

  • Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
  • Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.
  • SmartAudio input allows remote control by the flight controller (where supported). Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.
  • All parameters art controllable via push-button on the side of the unit, for case where SmartAudio is not used. 
  • LED Indicators of Channel, Band and Power. Allow easily check VTX Parameters by glancing at the quad.
  • Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.
  • 0.5mW Ture Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.
  • Built-in Microphone, so you can listen to your motors while you fly, no matter how far away you fly.
  • Standard 36mm form factor allows you to mount the Atlatl directly in your flight controller stack.

Specifications

  • Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
  • Audio: 6.5 MHz Mono
  • Antenna Connector: MMCX
  • Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts
  • Dimensions: 35x25x7mm (Includes USB height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 9.3g

Includes

  • 1x Tekko32 35A 4-in-1 ESC
  • 1x Kakute F4 V2 Flight Controller
  • 1x Atlatl HV V2 Video Transmitter

Resources

Additional Information
SKU 8914
Manufacturer Holybro
UPC (GTIN) 704817768909
Reviews

FPV Regulatory Notice

The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your area. It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. GetFPV cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.

Also Purchased